Search:

I'm open to any offers, i know i'm not going to get 4k $cdn, so offer away, what's the worst i could say? Due to my life situation i no longer have time or money to finish this car up, and i really...

this is pretty silly, but, i have used a router with a quality bit on aluminum lots of times before. with a radius bit it works nice for putting a radius on an aluminum hole, works well. when cutting...

i think you could do mounts up pretty well with pretty simple fab work, length wise (width in the engine bay) i think that there would be plenty of room. i would wonder about if the height of the...

for those particular ones look up nissan 240z fender flares on ebay.

not mood, strive for perfection to make other people envious of it, and want to buy one as well...:D

i think it would need to be a later 3spd like a 31th in a neon so it has the larger diff bearings, so as to clear and accept the awd ptu retainer and the very large bearing on the passenger side of...

^thats pretty cool, i am wondering about this kind of thing and ms in the future.

it reads to me like when he was stock springs it revved to 6500 then floated. coo, info here for sure, i too would like to know the rpm capability of the stock rockers.

that is the style of turbo, with the integrated bov, and available with the integrated wastegate. spendy but nice.
with the 8374 you'll be at the upper limits with the chp you want to make. it'd...

will do!, i think i actually might have pics of the header too somewhere. i'll be curious to take measurements from an l-body, simon has a old charger at his shop that i could use for what i'd need...

i dont know if the firewall to block clearance is tighter for an l-body, but the header will be built to be as drop in as possible, no removing the ps pump, or pushing in the firewall. one thing is...

the only cD i could find for a caravan was .35 for 96-2000. for the record the cD for a dodge shadow according to allpar and ecomodder.com is .42.
the van would be nice to have, having a little...

yup, i take it as he is using spacers/adaptors to use the wheels he likes.

gm pattern is 4x4.75" or 5x120. looks to use 2"spacers to use the corvette rims (lots of offset on the corvette wheels) and 1" ones to use 5x114.3 rims with probably less offset.

i think just about all k-cars and variants have a pretty poor cD. but look at it this way the new camaro zl1 has a cD over .40 which is worse than most coupes, and hotrod took a lingenfelter zl1 to...

one genius, and a rocket scientist.
fairly new to this thread but the innovation and creativeness is amazing. looking forward to new developments.

the aero on the shadow is horrible as well, the sharper lip at the front edge of the hood looks like it would cause separation at high speeds, the pic of turboshads carbon fiber hood bulging up while...

if the cams were out of phase by enough to not run, you wouldn't get 200 psi in #2. dumb question, is the distributor phased correctly? that wound up causing me my no run issue. will it still catch...

think of the sucker punch you could deliver to an opponent in a 500hp awd turbo minivan.. you dont get much more different than that. and it just so happens it could be pretty easy to build it,...

do a turbo 3l caravan and make simon jealous of the power band

for the record, you can get chrome rings that have a plasma moly coating on them.

not an expert at all, just good at reading and regurgitating facts and numbers ive read before, and following good advice after careful thought.

my thought was this, it takes major work to make a...

rule of thumb i kept seeing is stock cast crank up until ~550 whp with failures around 600 depending on tune. i kept reading ~600-700whp on stock forged rods. cast pistons? dont know, but i chose to...

i tigged mine with er70s-2 mild steel rod, so based on that i suppose regular mild steel mig wire. er70s-6? wire

i like it! but to clarify the situation will be worked out via the real father. just sayin. keep us posted as to your impressions of the header.