Search:

Type: Posts; User: wheming; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.68 seconds; generated 5 minute(s) ago.

  1. Replies
    265
    Views
    10,227

    Re: MPSciLink device pre-order

    Glad to hear.
    I didn't check the shipping updates yet.
    When you guys get things setup, let me know if you have questions. And refer to my cheesy videos, as i think i hit all the initial setup and...
  2. Replies
    12
    Views
    297

    Re: Roadkill's $3K Hooptie challenge

    Sometimes the track sprays a wide band of water, and other times the waterbox is narrow.
    Either way, to be sure you wet you whole tire circumference, you simply spin in the water. Then pull...
  3. Replies
    10
    Views
    172

    Re: PT GT/SRT Spindle

    I think they have the pressed in bearing like the pre-91. But, not sure if the bearing interchanges.
    Its too bad they didn't use the bolt on bearing.
  4. Replies
    10
    Views
    172

    Re: PT GT/SRT Spindle

    This is good to know. I have some things in mind for my projects, and sounds like this would fit in with those plans.

    PT spindles use a different wheel bearing? And is the spline different, or a...
  5. Replies
    15
    Views
    530

    Re: MPSciLink starting a Group3 Pre-Order

    Don't worry, you haven't missed anything yet. We are very close to opening back up the "store" webpage. Anyone in this group will receive a slightly redesigned board as we have identified some...
  6. Replies
    265
    Views
    10,227

    Re: MPSciLink device pre-order

    Forgot the progress pic!
    62198
  7. Replies
    265
    Views
    10,227

    Re: MPSciLink device pre-order

    Glad to hear it worked!

    There's no installation instructions, just refer to my help videos.
    I fitted and clearanced your enclosure, but you should see during assembling.
    If you have any...
  8. Replies
    265
    Views
    10,227

    Re: MPSciLink device pre-order

    Order #5-8 going out in tomorrow's mail.
    You should receive a tracking email.
    Brian B, Ian A, Sev, and Vic.
  9. Replies
    10
    Views
    182

    Re: 2.4 t-smec rev cutout - launch control?

    Sweet!
    Try again with those pics. Would love to see whst he has done with it! I don't know that he remembers me, but I've never forgotten that Rampage!
  10. Replies
    10
    Views
    182

    Re: 2.4 t-smec rev cutout - launch control?

    I had a similar issue at SDAC23 in Slug with a Turbonator cal. There was some hidden issue with that version # it was based from.
    Be sure you are using a v19.6 based cal. I can't remember which...
  11. Replies
    17
    Views
    312

    Re: 2.4 exhaust mani/header recommendation

    Pics not worky
  12. Replies
    265
    Views
    10,227

    Re: MPSciLink device pre-order

    All kidding aside, Miles is doing a bang-up job getting these boards built up as efficiently as possible.
    Thanks Miles!

    So I should get another bunch of them soon, so we really should be rounding...
  13. Replies
    265
    Views
    10,227

    Re: MPSciLink device pre-order

    Back to the sweatshop with you!
    I said you couldn't take a break until you built all available units! ;)

    That's the beauty of overseas manufacturing. ...you get to treat the help like dogs....or...
  14. Replies
    265
    Views
    10,227

    Re: MPSciLink device pre-order

    You should have asked your wife for your credit card earlier....
    He paid before you. Sorry...
  15. Replies
    265
    Views
    10,227

    Re: MPSciLink device pre-order

    You get the next one that goes out.
    Just fyi...
  16. Replies
    265
    Views
    10,227

    Re: MPSciLink device pre-order

    Update!
    I've received the 4 repaired units to close out the original purchase group (1). I've bench tested 2 units so far.
    Once i have them all updated and bench tested, I will test them on a...
  17. Replies
    17
    Views
    312

    Re: 2.4 exhaust mani/header recommendation

    I remember getting a ride in that rampage 20 years ago when i was at Merrill's shop with Gus, getting some exhaust work done on one of my vehicles at the time. (I think it was my Grand Cherokee...
  18. Replies
    17
    Views
    312

    Re: 2.4 exhaust mani/header recommendation

    Jon is that Merrill's trucklet you are working on?
  19. Replies
    305
    Views
    30,781

    Re: DriveShaft Shop Axles - Group Buy

    Unfortunately no. They've long since been recycled into Kia's and Hyundai's...
  20. Replies
    22
    Views
    508

    Re: GTP up for auction on BAT

    ^^^ That's who i was trying to think of! Thanks.
  21. Replies
    305
    Views
    30,781

    Re: DriveShaft Shop Axles - Group Buy

    62168
    These are the last ones i bought for Mini. The pass side is on now.
    I had some other new ones before this, and can't find the receipt.

    These I believe said that they were a bit longer to...
  22. Replies
    3
    Views
    175

    Re: Mini projector for a HUD ??

    That's interesting.
    Torque for Android has a HUD mode. But when I've used it in my PT, the dash isn't quite flat enough for the phone to sit. It would need a friction pad that was level.
    But,...
  23. Replies
    5
    Views
    311

    Re: DIY holset 351ve controller

    Cool!
  24. Replies
    265
    Views
    10,227

    Re: MPSciLink device pre-order

    You are #21 Ian, which puts you close to the back of the pack.
    Once we get a little further along with the folks in front of you, I'll be able to give you a better idea of delivery. But I'm...
  25. Re: Wideband installed, seems to run a bit rich

    Sorry, I guess I misread!
    The at idle AFR is after the engine is fully warmed/the fan has cycled on?
Results 1 to 25 of 110
Page 1 of 5 1 2 3 4