Hello all, recently picked up my old TD craze and looking into doing a megasquirt system for my SC. its a socketed 87 LM, if anyone has a tune for 83lbs injectors, wideband, 3bar i would buy it for a...
Type: Posts; User: Motorbreath; Keyword(s):
Hello all, recently picked up my old TD craze and looking into doing a megasquirt system for my SC. its a socketed 87 LM, if anyone has a tune for 83lbs injectors, wideband, 3bar i would buy it for a...
I need a wrecked large spline input shaft with an execlent or near new spline. If its broken in half it doesn't matter I only need the spline section.
If you could fill this request I will...
they have dohc heads there all the time. Wait for there head sale its like 50 for the head. I bought a head the whloe top end minus fuel rail because i forgot it and no exhaust manifold for under 100.
Removing that much material from the head you might what to check your valve to piston clearances. Exspecialy if your using a cam with more lift than stock. Your motor may not be non-interfercial(I...
I belive its a 91 trans but I still need to check it.
I think I will just leave it alone and try to find a better trans to but a obx in. Or try to find some better gears.
Thanks for the help.
Im curently trying to finishing my 2.2 hybird motor and I am starting to worry about my transmission. The car is a 1990 shadow es. In the end the car will not be a daily driver, but has to be for...
I would like to get the front spindles minus the shocks with all the brake hardware on them. I also want the master cylinder and maybe the proportioning valve.
Thanks again
If they are still there I will take the front brakes, rotors, spindles and master cylinder.
Just give me a call.
2 piece intake and fuel rail 150usd obo plus shipping
t2 rods with wrist pins 40usd obo plus shiping
Can send pictures if wanted.
Thanks Jason
2 piece intake and fuel rail for $230usd obo.
can send pictures
Also have a t2 compressor housing and small wastegate can for $50usd obo.
and t2 rods for $70usd obo.
All prices do not...
Number 156
http://www.missionraceway.com/mrpphotosvideos/06images/06may19fri/index.htm
Thanks For the pics.
I have finally free up some time and have starting on my Ajustible hybrid can gears. They will have 6061 aluminum centers with the original 8 valve cast iron gears (working on getting a gear cutter...
Long list but I thought I would ask before I buy this stuf new.
I am looking for a to4b wheel with the dimensions:
1.904 inducer
2.75 or 3.00 major dia.
with a .250 bore
It is a S or super S...
t3 intercooler from iroc daytona 50usd obo plus shipping
Has one tab removed when it was in my shadow
Have pics just pm me with your email address
Thanks Jason.
i did it to my charger and it is not that hard but does take some time.
send me a pm and i can walk you through it.
thanks jason.
new prices
50usd for the set
and 15 for the singles
I have 1 set and 3 singles
Set of 4 70usd + shipping
singles 20usd each + shipping
Can provide pictures if wanted
Thanks Jason
dont worry about shipping to Canada all my stuff is sent to Washington
I have a t3 intercooler out of a 92 iroc daytona that I was going to cut up for a 3 core when I relized it was around a inch taller then a t2 cooler.
So does anybody want to trade a there t2 cooler...
the pads are worn a bit but I did not think that was the problem. but now it might just of been the forks. I just cant find anything wrong with it. Has anybody else had a problem resembling this one...
I have a set the bolts rubers and the plastic piece 5usd + shipping
Thanks Jason
5 CDN dollars plus shiping I would send it for the shipping cost but I hate shipping.
Thanks Jason.
I personally think that there is a lot of stuff that cannot be in a kit.
Stuff like the dowel holes and the oil return holes. If you have a big enough drill bit you still need a tap. Not every one...
I will send a pic when I find my camera.
And it is just a stock .48a/r housing All i needed was the center section but I removed all th bolts with heat. Though some one might need it.