Search:

Type: Posts; User: moparmike70; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    1,475

    Re: Barometer reading off?

    I was able to read the first tune and save it on my computer but I can't do anything with it because it saved it as a bin file. From what I've read you can't read the bin file unless you have the...
  2. Replies
    10
    Views
    1,475

    Barometer reading off?

    89 Daytona 2.5l
  3. Replies
    10
    Views
    1,475

    Barometer reading off?

    Ok, I will set up the AF sensor with the gauge first because I think my set up doesnít have the conversion to run it in place of the O2. I have an Autometer gauge set up and the AF runs straight to...
  4. Replies
    10
    Views
    1,475

    Barometer reading off?

    When I put the wideband in I have to set the tune up for that correct? Iím assuming you want it set up so the ecu reads the wideband and not just hooked to a gauge.
  5. Replies
    10
    Views
    1,475

    Barometer reading off?

    I am willing to learn to do the calibration myself, I have been reading everything I can find on it and I have downloaded the appropriate programs to do so. Rob from BB did the tune that is in there...
  6. Replies
    10
    Views
    1,475

    Re: Barometer reading off?

    I am using a Snap on scanner. It has +40 injectors and the map reading itself I donít think is the issue as itís computing the value correctly (absolute+/-boost or vacuum). Itís just that the...
  7. Replies
    10
    Views
    1,475

    Barometer reading off?

    Not sure if this is the right section to post in but I think the problem lies in the tune. Needing some help with my newly installed engine. The vehicle is an 89 Daytona 2.5L with a 50 trim t3/4....
  8. Replies
    143
    Views
    24,167

    Re: 91+ A568 bronze shift fork pads

    Received mine the other day, thank you!
  9. Re: Scatter Shield - Reeves Racing/Creative Fabrication

    I'm going opt out, sorry.
  10. Replies
    19
    Views
    2,367

    Re: few questions on rebuilding 2.5l

    The seat would have to be removed for sure and replaced. As far going to a larger seat od I'm not sure if they would have to do that or not.
  11. Replies
    19
    Views
    2,367

    few questions on rebuilding 2.5l

    I would definitely bring it back to the machine shop. You risk dropping a seat if you don't confirm it. Dropping a seat equals instant carnage. Personally I wouldn't run the head myself with it like...
  12. Replies
    21
    Views
    2,674

    Re: When should I paint my engine?

    Looks like it came out pretty good
  13. Re: how to cut quarters and rear wheel arches off a gbody?

    The best way would be to drill out all the spot welds around whole quarter panel. It's less work, less filler and a cleaner installation to replace the whole quarter and if done correctly will last...
  14. Re: Gauging Interest- Chrysler .63 A/R turbine housing Group Buy

    Balance paid
  15. Re: Gauging Interest- Chrysler .63 A/R turbine housing Group Buy

    #14. Moparmike70-stage 2
  16. Re: Scatter Shield - Reeves Racing/Creative Fabrication

    I will buy one.

    1) chargerturbo87 -1- With timing window & With hardware
    2) moparmike70- 1-with timing window & with harware
    3)
    4)
    5)
    6)
    7)
    8)
  17. Replies
    21
    Views
    2,674

    Re: When should I paint my engine?

    Fyi, if you do by some chance get paint on any surface there shouldn't be just put some paint thinner on a rag and wipe it off just like that. Never use any abrasives. Keep the engine as clean as...
  18. Replies
    21
    Views
    2,674

    Re: When should I paint my engine?

    Anywhere there is a gasket and any part considered the "inside" of the engine should be clean and free from any paint. All freeze plugs should be installed before any painting and they can be painted...
  19. Replies
    24
    Views
    4,807

    General Re: Parting out 87 Daytona

    Is the steering shaft any good? Looking for one that's not binding. Price and shipping to 02766
  20. Replies
    21
    Views
    2,674

    Re: When should I paint my engine?

    I would paint it right away before assembly because you'll be handling oily engine parts at that point. Right when you get it from the machine shop will be the cleanest it will ever be.
  21. Re: Gauging Interest- Chrysler .63 A/R turbine housing Group Buy

    Deposit paid, stage 2
  22. Re: Gauging Interest- Chrysler .63 A/R turbine housing Group Buy

    I will be needing a stage 2 or 3 but not sure which one I need yet
  23. Re: Gauging Interest- Chrysler .63 A/R turbine housing Group Buy

    Put me down for one.
  24. Replies
    16
    Views
    2,936

    Re: 1" thick throttle body spacer (2.2/2.5)

    1. johnniroc (w/ port holes) (TM)
    2. 86seeS (w/ port holes) (TM)
    3. DOHCRT (TM)
    4. moparmike70 (w/portholes) (TM)
    5.
    6.
    7.
    8.
    9.
    10.
  25. Replies
    335
    Views
    48,199

    Re: Turbos Unleashed Cast Header

    Payment sent
Results 1 to 25 of 30
Page 1 of 2 1 2