Search:

Type: Posts; User: Aries_Turbo; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    4
    Views
    770

    Electronics Re: Dodge 600 ES digital dash with Tach

    if he doesnt, i think i have one.

    Brian
  2. Replies
    24
    Views
    772

    Re: Drag week 2019

    No it's 2 turbocharged 3400v6 setups from what I saw on 1320video
  3. Re: NV-T350 / F5MC1 differences for 2.4 and 2.7

    the 2.7 got the T850 and it has the bellhousing thats sized to fit the 2.7, the 3.3, the 3.8 and probably the 3.5 24v. maybe that 3.2 that they had as well.

    Brian
  4. Thread: Exhaust

    by Aries_Turbo
    Replies
    4
    Views
    252

    Re: Exhaust

    ive done this as well. works well.

    Brian
  5. Replies
    7
    Views
    210

    Re: Knock volts versus degrees of retard

    Look more closely. And go to mptune and look at this table. It is rpm dependent. Think of the knock sensor as a microphone. As the rpms rise, the overall noise of the block goes up. You can't have...
  6. Replies
    7
    Views
    210

    Re: Knock volts versus degrees of retard

    64340

    this is what defines whether there is knock retard.

    as you can see, even if you see 1.5v on the knock voltage readout, it can be below the threshold of knock as long as its above...
  7. Replies
    40
    Views
    12,491

    Re: Water Pumps - lets have a dscussion !

    i thought i saw a few mopar parts houses listing oem pumps for like 42$ or so....

    Brian

    - - - Updated - - -

    FYI im using a 180k oem water pump still. no issues..... probably because i have...
  8. Replies
    10
    Views
    796

    Re: OSTRICH WITH LM please help!

    did you scale the tune for 72lb injectors i assume?

    you can do one of two things.

    you can lower the pumping efficiency table overall until it idles and drives properly.

    or you can scale...
  9. Replies
    10
    Views
    796

    Re: OSTRICH WITH LM please help!

    you can also manually update the ostrich with emutility i believe. the rom should be written to the ostrich from C000 to FFFF memorly location for an LM.

    also, the ostrich can get goofed up and...
  10. Replies
    10
    Views
    796

    Re: OSTRICH WITH LM please help!

    all of the chips on the LM have a notch at one end indicating the location of pin 1.

    the chip would have a notch at the same end as the other chips.

    the red stripe on the ostrich ribbon cable...
  11. Replies
    10
    Views
    796

    Re: OSTRICH WITH LM please help!

    the ostrich works just fine with the LM.

    did you install the appropriate FTDI drivers?

    if you plug in the ostrich and the drivers are loaded, MPTune will automatically recognize the ostrich...
  12. Replies
    22
    Views
    1,367

    Re: Omni with 2.2 turbo engine codes woes

    Which post number is that. I have my posts per page set to like 40 vs the default 10.

    If you are asking about looking for an ECU, make a thread for a sbec in parts wanted.

    Also, make sure you...
  13. Re: 2001 2.4 motor with 2.5 rods and pistons.

    no i dont. i wish i did. i really havent looked hard though
  14. Re: 2001 2.4 motor with 2.5 rods and pistons.

    I also thought that people were having issues getting the harder performance bearings for the older rods. I know you can get them for a 2.4.

    Brian
  15. Replies
    22
    Views
    1,367

    Re: Omni with 2.2 turbo engine codes woes

    You can also disassemble the sbec connector (pull the red lock clips out and gently pry back the pin lock tab and slide the pin out) and remove just the sensors ground female pin and make sure the...
  16. Replies
    22
    Views
    1,367

    Re: Omni with 2.2 turbo engine codes woes

    As far north as you are, the air doesn't need to go through the computer. Arizona, yes, Canada, probably not.

    The sensor signal ground is different from the power ground (injectors/coil/fuel...
  17. Replies
    22
    Views
    1,367

    Re: Omni with 2.2 turbo engine codes woes

    also, the 60 pin connectors on the ECU in the engine bay can develop loose pins after all these years and can then do goofy things. try unbolting the connector and re attaching it.

    wiring on...
  18. Replies
    22
    Views
    1,367

    Re: Omni with 2.2 turbo engine codes woes

    sounds like the 5v to the sensors or the sensor ground is missing.

    id start there.

    minimopar.net has fault code stuff and wiring info.

    also, did you weld on the car with the ecu installed?...
  19. Replies
    34
    Views
    1,067

    Re: Turbo Mom Van

    For real. That thing is awesome.

    Brian
  20. Replies
    309
    Views
    53,509

    Re: 10 second 190,000 mile low boost 3.0 build

    Yeah it takes me forever to get things done so I split it up into tiny tasks. Last summer I swapped smec connectors onto the LM harness. I soldered like 5 wires a day lol.

    The new AMD stuff is...
  21. Replies
    309
    Views
    53,509

    Re: 10 second 190,000 mile low boost 3.0 build

    Ah yes.....baby jail. I know that all too well lol.

    And car sitting for 8 years too.

    Brian
  22. Replies
    4
    Views
    399

    Re: P body window scrapers

    looks like 1/2" is better for a reliant. im gonna order some.

    Brian
  23. Replies
    4
    Views
    399

    Re: P body window scrapers

    is the shadow exactly 3/8" to the window?

    im looking for stuff for my reliant and it looks like the reliant is like a 1/16" or 3/32" more than 3/8"

    also, is it really 42.20 for 2 pieces? it...
  24. Replies
    12
    Views
    843

    Re: Exhaust bolt installation issue

    I've always used vise grips to help the flange closed.

    I also tack welded a nut to my swingvalve housing next to the turbine housing. I start that one first. Then use the vise grips to help the...
  25. Re: 1988 CSX-T (SHADOW ES) AC conversion to R134a

    AC can side tap. eBay 10$ when I got mine.

    I've seen folks charge r12 with it and r134a. You just gotta be mindful of the oil because it's closer to r134a molecularly.

    You need less of it...
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4