Search:

Last year I learned that VMS was going to start offering some wheel options in 5x100. Around this time, I also found that they were offering a pretty good Black Friday sale as well. It was 25% off...

I'm not sure that Shadows ever got the high torque option.

I missed how the individual cals are selected. ?

I tried copying it with the correct time stamp twice and I thought I had it working

*Edited* let's try this again

Mike should be at 2:53 https://youtu.be/a3PHzPrx8FU?t=10377
I got to see him boogie off the line but didn't have any clue he ran a 9!

Wayne ...

1993 --- Sundance --- 2.5L T-II FMIC --- A568(3.50:1)TSquared --- 23x8.5x15 M&H Slicks --- Dan Hemingway--- Dan H --- U.S.--- 60' (2.076) --- 1/8ET (8.73) @ MPH (85.79) --- 1/4ET (13.291) @ MPH...

At Cecil I lost one of the grounds at my battery terminal and the car died mid pass. Easy fix, but not enough time for a second run when the next drive was more important.

Turboshelbys is parting one right now.

I don't think either should have any effect on the issues you are experiencing. They are only needed for protection if you are using the cable to flash a SBEC. For a SMEC, I'm pretty certain you...

If you want a quick test that might work without any soldering... assuming you can get a good enough connection just by holding it in place. Take that extra green wire that goes to the "Bt" spot. ...

I'll resist asking where it came from.

I'm guessing it doesn't pass the cable test in MPSCAN or MPTUNE, whichever has it? Where you jump the RX and TX blades and run the cable test to make sure...

Sounds like you have every correct. If you have the right Com port selected in MPScan but it displayed generic in the lower corner you can just close the program and re-open. It should then list...

Thanks Miles

They are low impedance injectors.
A or B was only a reference to my two initial descriptions in the first post. Those were the driver types for the two separate specs they provided.

Thanks for checking Miles.

I'm asking because I received battery offset data for an injector. It has different scales for type A or B

Which of the following would best describe the factory injector drivers:
A) 2 amp Peak, 0.5 amp Hold, 43V Zener Voltage Suppression, 14.0 VDC

B) 4 amp Peak, 1 amp Hold, 4 ms timer,...

Thanks Rob. I thought I had seen a mention before like it would be most accurate being perpendicular to flow. I was hoping that the wastegate boss wouldn't be enough in line with the cylinder 2...

Well, I guess that is where I will try.

Would the external wastegate boss on a TU cast header give an accurate reading of drive pressure?

Interesting, I didn't know that. Does that go for both the early and late style? I was having difficulty when I tried to install a late one and ended up just putting a stock style in for the time...

I would probably first check the engine positioning after doing the passenger side mount. Did you need to re-adjust after putting it in? Did your passenger side have the two flat spacers?

Nice job! I'd like to see more info about the ethanol sensor setup. I was going to try this: https://www.audizine.com/forum/showthread.php/797848-DIY-Arduino-Ethanol-Content-Analyzer
It's on the...

I had a 11's all around on my 89 Shadow. I had the back sweep around on me a few times.

I haven't gotten on these brakes that hard yet. I have a Wilwood adjustable proportioning valve I plan to...

Not to hijack, but what are the factors in picking the best matched master. One of my cars has the 10.xx" inch fronts with the 11" vented in the rear at the moment. I think my master has a slight...

I haven't exactly found an answer searching the Web about Microsquirt or Megasquirt.

I saw in your first post you list "o2 sensor (AEM Uego with 5v output)".

Do they allow for the use of a...