Email sent!
Type: Posts; User: ShelbyZD; Keyword(s):
Email sent!
ok good to know. Thanks! Got some info from NAJ too.
Hi I got 2 questions:
1. 1992 Daytona Iroc R/T has no underhood wiring. Can I use the underhood wiring from a 92 Daytona 2.5 NA and temp install a 2.5L NA engine and have it run without burning...
I had +20 injectors with a stage 3 15psi fwdp cal on a 2 bar, grainered to 22psi with the meth/water inj. It was super fun! lol Fried my fat 15" 225 wide tires off in 2nd up to 100kph. I have...
I have thought of it and have tinkered with the software and looked at some cal files, however I am not familiar enough with the software vs engine tuning to risk it.
- - - Updated - - -
Hi...
I already contacted FWD-P and received no reply(yes I know they are partly retired). I need a 22psi chip for my 88 Daytona Shelby Z (stock garret). I have a 3 bar map, +40's, 50/50 meth/water...
I'm looking for just the underhood harness but will take the whole thing if necessary. I'm converting my 88 Lancer to a 2.5L turbo and also need the underhood wiring from a 92 Daytona turbo for my...
This may be too late, but its good info to have anyway.
http://www.turbo-mopar.com/forums/knowledge/pictures/ecu/ecu_listing.pdf
Thanks for the reply Martin. I already have a few 88/89 turbo ecu's I can use, so I guess I just need an underhood harness specific to am 88 Lancer or Gts Lebaron (h-body).
Hi guys, I am looking for:
1992 Chrysler Daytona Turbo underhood wiring and ecu (Turbo1). (I'm not sure if it has to been a Daytona harness)
1988 Dodge Lancer underhood wiring and ecu. (Again,...
ok thanks guys! MBC it is. Is there a cheaper or better solution than a granger valve? Can I use any of these cheap ones?...
Hi all, my father installed a Stage 3 BB ecu (16psi) in his 89 Shelby Daytona. I installed a Stage 4 BB ecu (18psi) in my 88 Daytona Shelby Z...along with the injectors and 3.0 bar map sensors.
We...
Has anyone had any luck with the new mp headgaskets while making 260-270hp and 22psi boost (stock turbo)?
I had a failpro P9296Pt and it blew between 1 and 2 cylinders likely due to them not...
Do you have the h-body underhood wiring?
Nice, its cool went you can hang on to your 1st car (or keep your new car for a long time). Sadly my white 88 N/A Daytona was scrapped early 2000's. I would have saved it if I had been wiser then. lol
Hi, I need is a good condition 87-88 A520 ring gear and
intermediate shaft, to swap into my 1988 A555.
I'm swapping to the 3.50fd and installing a limited slip differential. Thanks!
From my brother:
"Thank you guys for helping me to identify the "left" shaft in the pics
above, as an 89+. I'm not sure yet exactly what happened, but about 5
years ago we bought an 87 Daytona...
Ok, this is what my brother Richard says,
"Thanks for your reply's, you are correct, that is what the re-tired Chrysler tech told me... (he is the 1 that is building my hybrid transmission)... my...
My brother is trying to get his TU LSD to install in his 1988 A555. He is using parts from a 1987 A520. I don't know for sure what's wrong but I believe there is a problem with the 1st gear barely...
Does anyone have spare hardened washers they want to sell from their previous PT Cruiser lifter upgrade they can send to Canada?
I could use 24 for 3 heads. Let me know thanks!
Thanks, I realize the quaife is available.. was hoping someone had an obx to sell as you can't get them new anymore.
I need an OBX for my 555. I may consider a full transmission. Let me know what you have and how much you want for it.
Thanks!
Ok, thanks for the info. I do have the bottom plug plugged in, it's the top high pressure cutout switch that I can't connect.
Dr Johnny Dodge which hoses are you talking about? The earlier 80's...
1990 Chrysler FSM.
Ok, my car didn't have AC from the factory, so I am working at installing it. I used the following parts from newer cars:
1. Heater box with AC stuff (controls, Evaporator) from my 89 Shelby...