Search:

Type: Posts; User: chromguy; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    15
    Views
    477

    Re: Headlamp Adjuster PN 4334142

    Cordes,
    So would the 11718 fit my 87 P bodies?
  2. Thread: SMEC Code 43

    by chromguy
    Replies
    11
    Views
    353

    Re: SMEC Code 43

    Sounds great Randy that a new ASD relay fixed the issue
  3. Thread: SMEC Code 43

    by chromguy
    Replies
    11
    Views
    353

    Re: SMEC Code 43

    Hi Randy,
    the coil + is connected to the ASD so hot when IGN is on. The negative is controlled by the power module and will pulse with every coil firing
    It could be bad caps on the power module....
  4. Replies
    1
    Views
    315

    Re: MP Flash switch setups

    There are many different kinds of switch that are possible with MPFlash. Last year, I use a two switch in the classic binary config as per
    0,0 is position 1
    0,1 is position 2
    1,0 is position 3...
  5. Re: New Flash Product Development, and Pre-Order interest

    Hi Jeff,
    Here is the link that should answer all your questions.
    https://sites.google.com/view/mpflash
  6. Replies
    27
    Views
    1,456

    Re: Trans rebuild parts availability

    Ratech cancelled my order in late 2020, I thought is was because I am a hoser...
  7. Replies
    27
    Views
    1,456

    Re: Trans rebuild parts availability

    Jackson says to buy shim from McMaster-carr
    I got mine from a local transmission shop who let me dig through a large box of shims for free.
    Nice, later I contacted them to press the bearings on my...
  8. Replies
    16
    Views
    1,391

    Re: Heater blows cold

    nice suggestion Johny
  9. Replies
    9
    Views
    907

    Re: Overcharging issue, 86 2.2 Turbo LeBaron

    Congrats!!
  10. Replies
    2
    Views
    692

    Re: Omni replacement door seals

    Very nice

    - - - Updated - - -

    Where did you purchase? and part number? Thanks
  11. Replies
    67
    Views
    11,788

    Re: JamesMonty's 85 GLH-Turbo project log

    I have also followed the suggestion of evaporust a few years back....Worked like a treat
  12. Replies
    14
    Views
    1,917

    Sticky: Re: TM Knowledge Center Update 2022

    How about you reference TM on the SDAC FB?
  13. Replies
    14
    Views
    1,917

    Sticky: Re: TM Knowledge Center Update 2022

    Cannot argue with that
  14. Replies
    14
    Views
    1,917

    Sticky: Re: TM Knowledge Center Update 2022

    Thanks JT for the update!
  15. Re: TU working with Ken@5 Digits to offer Calibrations, but, is there demand?

    Mark... this is very nice of you.
  16. Re: Converting a V6 SBEC2 to turbo code using pulse and hold

    Oh thanks to Randy for the SBEC2-377 donation;)
  17. Converting a V6 SBEC2 to turbo code using pulse and hold

    The objective of this project is to convert a V6 SBEC2 into a Turbo ECU, complete with pulse and hold injectors.
    The other day I removed all the V6 driver stuff and replaced with turbo 4 stuff. ...
  18. Replies
    13
    Views
    686

    Re: Who services injectors?

    I used my simulated narrow band signal from my 14point7 WB but found the engine went lean too quickly after starting before the engine was warm. I switched back to narrow band O2 control. Yes I could...
  19. Re: running a SBEC2 ECU on a 90/91 SBEC wired car

    Other ideas would be to either
    1)switch to high Z injectors and reset the error bits of the tune
    2)use an inline 10 Ohm power resistor. This will change the latency of the injector so a retune is...
  20. Re: running a SBEC2 ECU on a 90/91 SBEC wired car

    Well not super simple.
  21. running a SBEC2 ECU on a 90/91 SBEC wired car

    As we all know, a SBEC2 is very different than an SBEC and you cannot simple plug it in. I have found and tested a solution simply place a jumper between pin#8 and pin #57 either in your harness or...
  22. Thread: piston's ?

    by chromguy
    Replies
    4
    Views
    470

    Re: piston's ?

    a google search shows
    https://www.wholesalemoparparts.com/p/Chrysler__Laser/PISTON/59893812/5241059.html
  23. Thread: Davis Vizard

    by chromguy
    Replies
    7
    Views
    624

    Re: Davis Vizard

    I am buying rubber mold kit to start
  24. Replies
    12
    Views
    2,333

    Re: MPFlash Batch#2 Interest/Pre-Order List

    I did locate a few chips so we can make OctoPlay. Another year or so will will be able to buy these in lots of 5000...
  25. Replies
    11
    Views
    957

    Re: Help with SMEC

    Why would your bolts need to be scratched?
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4