Search:

Type: Posts; User: krut; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    385
    Views
    53,855

    Re: DriveShaft Shop Axles - Group Buy

    Any news on this?
  2. Re: Interior Fuse Block Replacement (Aftermarket preferred)

    Nope. You need to order the colored shells and pin it out yourself. It's not hard.
  3. Re: Interior Fuse Block Replacement (Aftermarket preferred)

    That's really cool. I was thinking about how these are used on IH's. The fuse panel clips all together like relay holders. You can pop off / pop on pieces as needed. I always wondered if someone took...
  4. Re: Interior Fuse Block Replacement (Aftermarket preferred)

    That's the HWB series. They also make smaller ones than the one you listed. So say you have like HWB16, which is a 16 pin box, etc. Some are made specifically for say 4 fuses.

    I haven't played...
  5. Re: Interior Fuse Block Replacement (Aftermarket preferred)

    I have one of those RTMR's actually. It's the one I used to replace the PDC up front. It takes up about the same space as that once it's all done. It may be a bit taller. If you're interested in...
  6. Re: Interior Fuse Block Replacement (Aftermarket preferred)

    I can't stress this enough: Bussman, etc. publish engineering drawings of the parts. Make sure it fits where you want. Some of the RTMR products are DEEP once you add relays, etc. The engineering...
  7. General Re: Looking for brake proportioning valve 4485829

    Found. Thanks.
  8. Re: Interior Fuse Block Replacement (Aftermarket preferred)

    https://www.waytekwire.com/products/1611/Power-Distribution/
  9. General Looking for brake proportioning valve 4485829

    Looking for proportioning valve PN 4485829.
    89 catalog lists it as for an 89 G Body, 15 or 16" wheels.
    Thank you
  10. Replies
    385
    Views
    53,855

    Re: DriveShaft Shop Axles - Group Buy

    I remember reading that. Just wanted to make sure that if I had these if I had to trim them out of the box so that I'm fully prepared
  11. Replies
    385
    Views
    53,855

    Re: DriveShaft Shop Axles - Group Buy

    Would the quaife axle shaft ends need to be trimmed?
  12. Replies
    385
    Views
    53,855

    Re: DriveShaft Shop Axles - Group Buy

    Is this still going on? If so,
    G-Body - L5 555 Quaife
  13. Thread: Lost another one

    by krut
    Replies
    43
    Views
    4,316

    Re: Lost another one

    Gotcha. Keep in mind this stuff is rated to last ~600k miles as long as it stays in the cooling system (;
  14. Thread: Lost another one

    by krut
    Replies
    43
    Views
    4,316

    Re: Lost another one

    Okay. I figured there was a good reason. I am planning to run the equivalent Shell / Cat ELC coolant myself. Mainly because we stock it by the pallet, and it's reasonably priced. (~$10/gallon) - 6.0...
  15. Thread: Lost another one

    by krut
    Replies
    43
    Views
    4,316

    Re: Lost another one

    What made you decide on a truck coolant?
  16. Replies
    1
    Views
    694

    Rear washer reservoir Daytona

    Can anyone chime in on the capacity of a rear washer reservoir on a Daytona? I'm thinking about adding one for a meth tank. I don't want to go through the work if the tank does not hold a lot of...
  17. Replies
    4
    Views
    634

    Electronics Re: Need headlamp module 4503024

    Found one. Thanks
  18. Thread: Lost another one

    by krut
    Replies
    43
    Views
    4,316

    Re: Lost another one

    If you're looking for a place for a head job, I'd suggest Precision in Hyatsville.
    My buddy uses them for head jobs for work, I've used them, and also a few friends. I have not had any real problems...
  19. Replies
    4
    Views
    634

    Electronics Re: Need headlamp module 4503024

    Yes. I have read them. This one has been repaired before, however. I'd rather start with a fresh one.
  20. Replies
    4
    Views
    634

    Electronics Need headlamp module 4503024

    As title says. Need G-Body headlamp control module. Looks like the one in the car melted, and the backup one I have is also melted.
    Thank you.
  21. Replies
    42
    Views
    2,963

    Re: Which TB to choose ?

    Do the srt4 throttle bodies share the same bolt patterns as the t2 tb's?
  22. Replies
    10
    Views
    1,141

    Re: Fuel filter modifications?

    I'm going to go forward with this once I get to that point in reassembly. I will first ask a Cat technician to see if there's anything to be concerned with.
  23. Replies
    2
    Views
    908

    Re: 89 Daytona not charging

    Have you tried full fielding the alternator momentarily to see what voltage is at the battery?
    Check the wiring for the regulator from the computer to the alternator.

    If you have very high...
  24. Replies
    10
    Views
    1,141

    Re: Fuel filter modifications?

    The filter I'm looking into would be a short version of the 1r0749, which is used as a secondary fuel filter on say a C15 cat. I *think* that pressure readings there are normally 80 - 100psi. This is...
  25. Replies
    10
    Views
    1,141

    Re: Fuel filter modifications?

    It's not so much because of a factory location. I am more curious if a diesel filter will work.
    At any given time, I have 30+ 1r0750's in stock. They filter to 2 microns for HEUI injection systems....
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4