Search:

Type: Posts; User: 135sohc; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    That would have to be a lot of flexing to see it without some sort of strain gauges mounted on there ?
  2. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    plate flexing and the ball bearing float. Even brand new those bearings have some side-side slop, plus the slop of sitting in the aluminum bulkhead. It all adds up to be 'alot' when were talking in...
  3. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    Earlier transmissions have a bronze bushing in the extension housing.
  4. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    Looks good :nod: Hopefully the extra time setting things up and knowing all the moving pieces are as in-spec as possible will pay off.
  5. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    The T850 shafts snap-off because of that built in torque fuse the manufacturing process dictates...

    Other than the larger vs smaller splines the diameter of the input shaft after the splines is...
  6. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    Wonder how the Getrag unit used in the PT cruiser would hold up ?
  7. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    Same idea as a 520 or 555, just a little more refined with the addition of those rubber washers to keep things quieter.
  8. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    maybe add some length to the spacer block so its not allowing the gear to slide back as far ?
  9. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    Are both of those input shafts the same first gear ? the one you busted looks like a 92-93 1st gear, the replacement a 91 and older 1st gear.
  10. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    with the pinion shaft removed from the case you can put that expanding tool you bought and measure the turning torque of the diff to get an idea of condition.
  11. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    In all your changing of parts have you ever checked to see how much end-play the input shaft has ?
  12. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    Still running just 2 pads on each fork ?
  13. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    stud it
  14. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    How loose of a fit is it between the input shaft splines and the clutch disc splines ? I have seen it on a few input shafts where the splines were very worn/edges rolled over from higher power...
  15. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    How rolled over are the splines on the input shaft ?
  16. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    A few times in the past when I was inquiring about different 523's listed for sale the sellers in multiple cases stated they were from N/A G & J body cars.

    I dont feel like looking for it right...
  17. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    minivan, daytona and lebaron I believe.
  18. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    Someone here cut the center out of a 568 ring gear so it could be used with the OBX.
  19. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    You sure know how to break stuff.... :thumb:

    For some reason every time I have drained the soup out of my 568 it has that same color. I can see brass, aluminum and even some darker (steel??)...
  20. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    An insert might help by reducing thread wear/damage vs the bolt being torqued directly into the aluminum bulkhead especially if its being taken apart frequently but otherwise I just cant see it...
  21. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    You were putting loctite on them right ?

    I wonder if theres enough room to put a BHSCS from the backside/inside and make it act like a stud ? An entire end cap bearing plate like the older...
  22. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    Will be awaiting the carnage shots ;)
  23. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    Anyone gonna try/check Jacksons idea of drilling/tapping and adding some tiny button head screws to keep the race from pulling off ?
  24. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    They have the tube setup like ours that the tob rides on.
  25. Replies
    3,391
    Views
    1,013,760

    Re: BadAss SRT-Z - 2.4L / A568 - Update!!!

    I read somewhere that NV-G cut the clutch splines with a broaching procedure and that requires an undercut.
Results 1 to 25 of 60
Page 1 of 3 1 2 3