Search:

Type: Posts; User: 135sohc; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    4
    Views
    495

    Re: Dill Blox Interior Electrical Panel

    Seeing this take shape makes me interested..
  2. Replies
    7
    Views
    1,025

    Re: WOW, That'a a lotta Spam...

    When a new member joins they have to get 'approved' by a staff member before they can start posting ? That would most likely eliminate 99.995% of the spam from ever occurring ?
  3. Replies
    4
    Views
    618

    Transmission Re: K body clutch pedal

    It would.

    I should correct/clarify to mean that anything from a K based car except the really early stuff should all be the same and compatible.
  4. Replies
    2
    Views
    1,251

    Re: Mecum had this 18k mile CXS

    I thought hell would freeze over first before anyone could say something nice about a P body.
  5. Replies
    4
    Views
    618

    Transmission K body clutch pedal

    I am looking for a K body type (not L or Minivan) clutch pedal.

    The pedal, the shaft it pivots on, the two springs, the steel spacer bushing and the two plastic pieces.

    I don't need nos and...
  6. Replies
    40
    Views
    19,506

    Re: Water Pumps - lets have a dscussion !

    So are they taking a stock (parts store junk replacement) pump and putting a new impeller on it ?
  7. Replies
    8
    Views
    1,167

    Re: Head locator pins missing - big deal or no?

    I use the studs to make the alignment. Those little pins are the source of many an unknowingly screwed up deck surface.
  8. Replies
    4
    Views
    781

    Re: P body window scrapers

    You can buy universal sweep material and cut to length. Remove all traces of the original rubber lip and graft the new piece onto the original stick with small pop rivets, urethane ect.
    ...
  9. Replies
    11
    Views
    1,878

    Re: Floor Pan Restoration

    There are some universal type floor pan patch panels/sections out there from places like EMS automotive and I'm sure others. I just finished up fixing a rust hole inside the rear wheel well on my...
  10. Re: SAE 30R9 versus SAE 30R14 Fuel Injection Lines

    http://www.hoseclampkings.com/cat-44-1-52/s40-w4-304-ss-screw.htm

    Buy once and never regret it.

    Mcmaster carr also sells them in 5 packs for about $10, but they also dont gouge you on shipping.
  11. Replies
    9
    Views
    1,333

    Re: Can't install LSD in A555.

    The shaft where the three splined areas are all similar is an 87-88 style, the other shaft where the two sets of splines are similar and the third set closest to the pinion gear are totally different...
  12. Re: 1988 CSX-T (SHADOW ES) AC conversion to R134a

    On the flanges of the receiver-dryer I have used anaerobic sealant when nothing else would seal it up.
  13. Re: 1988 CSX-T (SHADOW ES) AC conversion to R134a

    You've got the right idea, change as much as you can. The pressure switches you will probably not find new anymore so clean and reuse unless you suspect they are not working correctly.
    There is no...
  14. Replies
    12
    Views
    1,209

    Suspension Re: Rear bump stops

    If exact OEM appearance was not a concern those would be not too difficult to make with plate stock and round tube. Mine are somewhat crunchy and even on southern cars they catch moisture and rot...
  15. Replies
    12
    Views
    1,209

    Suspension Re: Rear bump stops

    Johnny @ polybushings has the upper and lower spring insulators.
  16. Replies
    15
    Views
    2,384

    Re: 93 A523 transmisson question.

    1/4" npt works also.
  17. Replies
    15
    Views
    2,384

    Re: 93 A523 transmisson question.

    That stud is for adjusting the cross-over shift cable, in normal mode the tapered longer end is up and when adjusting the cable you flip it over and thread it in to lock the selector shaft into...
  18. Replies
    21
    Views
    4,154

    Re: Omni GLHS alternator harness replacement

    The denso alternator is an improvement/upgrade over anything else so I would keep that and make everything else work towards it.

    The ECT connector is a metripack 150 series connector and terminals...
  19. Re: Cross-over hard brake line the same in all K-based cars?

    Anyone actually tried/seen the AGS flareforce tool in person ?


    I have the mastercool, eastwood and 5-6 other 'this is the one' flare tools... The holding dies on the mastercool really munch...
  20. Thread: Csx vnt #42

    by 135sohc
    Replies
    165
    Views
    35,573

    Re: Csx vnt #42

    The energizer bunny at work !
  21. Re: Cross-over hard brake line the same in all K-based cars?

    The different wheel base lengths are going to come into play. Each wheel has its own dedicated hard line from the prop valve and there are no splices built in (as originally made).
    expensive but...
  22. Thread: Csx vnt #42

    by 135sohc
    Replies
    165
    Views
    35,573

    Re: Csx vnt #42

    The diverter plate is a T3 thing, if you use it be sure to add a washer/spacer the same thickess at the long through bolt/stud so the housing sits level otherwise it will crack.
  23. Replies
    22
    Views
    2,178

    Re: Woosh from brake booster

    Thermocure from Walmart as a system flush. Talk about amazing, I start getting heat output in 2 minutes.
  24. Replies
    26
    Views
    3,270

    Re: 1988 LeBaron 4 dr 2.5 TBI

    On the k based chassis the track bar and angle brace is like perfectly in the way. I can do the pump on a P body with the tank installed but dropped down and supported on a thick piece of plywood and...
  25. Thread: 2D CAD Files

    by 135sohc
    Replies
    7
    Views
    12,265

    Re: 2D CAD Files

    We got a VF3 at work last year and the head engineer got it in his head that fusion 360 was the be all end all... So we all got the trial software and no one liked it. Autodesk called and email...
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4