Search:

Type: Posts; User: Aries_Turbo; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    10
    Views
    3,366

    Re: Cold Enrichment Tables CurveA, B, and C

    not real boost.... like less than 3psi.

    brian
  2. Replies
    10
    Views
    3,366

    Re: Cold Enrichment Tables CurveA, B, and C

    i havent adjusted them much either. they arent barfing fuel rich but I wouldnt mind taking a little out during really cold warmup.

    if i start it up and head out, then i cant roll into boost...
  3. Replies
    78
    Views
    11,957

    Re: Microsquirt

    I have that same crank trigger wheel. Wayne was selling adapters to run it on a common block. see if he still has some remaining units. he was selling sensor brackets too and they work. be careful if...
  4. Thread: MPScan

    by Aries_Turbo
    Replies
    572
    Views
    242,824

    Sticky: Re: MPScan

    shucks, i didnt see this till now or i would have texted or emailed you to try to correct it.

    ill put it in my list of reminders. can you send me the cal that is working?

    Thanks

    Brian
  5. Replies
    78
    Views
    11,957

    Re: Microsquirt

    some use toyota yaris coils, some use honda K series coils, etc. they just have to be logic level triggered coils. and yeah you would need to make a bracket to hold them.

    i did read of some...
  6. Replies
    78
    Views
    11,957

    Re: Microsquirt

    you should be able to use 2 spark output channels and do wasted spark COP with some resistor changes on the logic outputs to the coil triggers.

    Brian
  7. Replies
    78
    Views
    11,957

    Re: Microsquirt

    shucks, i wish I knew what state you were at for what you knew about what the microsquirt can do.

    yeah it can only do (oops edit) HIGH impedance injectors and it needs a coil driver module or...
  8. Replies
    78
    Views
    11,957

    Re: Microsquirt

    or a cheap 12v LED light bulb.

    youll have to make sure the polarity is correct.

    Brian
  9. Replies
    78
    Views
    11,957

    Re: Microsquirt

    12v rated LED. (LED with a resistor to make it able to handle 12v)

    Brian
  10. Replies
    78
    Views
    11,957

    Re: Microsquirt

    do you have spark? (even at the wrong time) or fuel injector pulse?

    Brian
  11. Replies
    5
    Views
    1,441

    Re: Error bit mask in MPTune

    no worries. if you need some help, you need some help.

    the SRT sensor is incompatible with our electronics. its a wide range sensor, like a microphone with no frequency filter. the stock sensor...
  12. Replies
    5
    Views
    1,441

    Re: Error bit mask in MPTune

    http://www.turbo-mopar.com/forums/showthread.php?23368-Turbonator-SMEC-codebase&p=1138484&viewfull=1#post1138484

    ; 26 Injector Current Limit Not Achieved 16,17,18
    ; 27 Injector Driver interface...
  13. Replies
    16
    Views
    2,677

    Re: OTC 4000E Advance reading

    fine. its a reference number used only to set the distributor position so that the calculated timing values are what the engine experiences. it has nothing to do with the advance the ECU calculates...
  14. Replies
    16
    Views
    2,677

    Re: OTC 4000E Advance reading

    no. that is an arbitrary number that is only used to set the distributor timing.

    Brian
  15. Replies
    16
    Views
    2,677

    Re: OTC 4000E Advance reading

    i wouldnt rely on regular jack stands. I would probably build a wood structure to sit the front "frame rails", k frame and/or and pinch welds on. and then a couple of straps on either side to heavy...
  16. Replies
    160
    Views
    194,218

    Re: The Neon thread!

    i loved my neons too. my wife drove a 98 dohc atx over 200k, and then a friend that we sold it to, drove it for 50k more. i had a 97 sohc atx and i drove mine over 200k and then sold it to a kid who...
  17. Replies
    16
    Views
    2,533

    Re: Distributor drive tabs have been freed!

    nice, Todd!

    Yeah Jon, the factory distributor spinning backwards is an inefficient pump.....

    Brian
  18. Replies
    16
    Views
    2,677

    Re: OTC 4000E Advance reading

    yeah the flywheel notch would work but it only reads to like 12 or so... in vac, you can have way more timing than that to verify.

    dyno before the computer, hydraulic pump against an orifice,...
  19. Replies
    26
    Views
    9,150

    Re: clutch adjuster plastic pieces

    for those in the 3d printing realm, prusaslicer can convert the step file to .stl for printing.

    Brian
  20. Replies
    16
    Views
    2,677

    Re: OTC 4000E Advance reading

    i dont know. MPSciLink shows a slightly different value than what I expect it to be, the OTC shows another value, the calculated advance 3d map shows a different value.

    the only way to really...
  21. Replies
    24
    Views
    7,668

    Re: SMEC Fuel Trim logging

    you can do that, especially for a quick test. for the long term, I would run the pressure that the injectors are rated to flow at.

    Now for a flowy build with ported manifolds, headers, good...
  22. Replies
    24
    Views
    7,668

    Re: SMEC Fuel Trim logging

    id add fuel in pumping efficiency from 2500-4500 range looking at some of your afr values, when you rescale to remove some fuel.

    Brian
  23. Replies
    24
    Views
    7,668

    Re: SMEC Fuel Trim logging

    when you rescale what you have for a larger (numerically) injector size, it scales the Part/Full/Baseline fuel tables.

    Save a copy of what you are running now and then when you rescale, start with...
  24. Replies
    24
    Views
    7,668

    Re: SMEC Fuel Trim logging

    looking at the majority auto cal cells, the ecu is pulling ~20 percent fuel to stay around 14.7 at part throttle/vacuum. you could stand to scale for a larger injector size (10% or so) and see if the...
  25. Replies
    26
    Views
    9,150

    Re: clutch adjuster plastic pieces

    nice! i like it. you going to be making and selling these?

    Brian
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4