Search:

Type: Posts; User: 87blueshelbyz; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    1,352

    General Re: Shifter, books, rad, tb, etc..

    Quote on the radiator to Baltimore MD 21234 if "vntned" does not buy it.
  2. MPScan says that I have 42 degrees advance at an idle

    The adv gauge says that I have 42 degrees advance at an idle. My OTC 4000e reads 12 degrees advance at an idle. I have a 87 T2 Dodge Daytona Shelbyz with a logic module. I have the stock tune and a...
  3. Replies
    2
    Views
    698

    Fuel T2 two piece intake fuel rail

    Looking for a T2 two piece intake fuel rail for a 87 Dodge Daytona Shelbyz. Must be in good condition.
  4. Replies
    16
    Views
    1,824

    Re: GLHS ground wire upgrade

    Yes, you are correct, The alternator ground wire is spliced in to the engine ground wire which connects to the negative side of the battery terminal.
  5. Re: 86 Daytona: runs like crap after 2 years of sitting

    If you drop the tank, I would replace the strainer on the fuel pump. Cut your old fuel filter open and look for rust on it. I had to replace my tank because it was full of rust.
  6. Replies
    5
    Views
    963

    Re: 85 ASD relay problems

    https://www.allpar.com/fix/codes/sensors/auto-shutdown.html
  7. Replies
    9
    Views
    5,615

    Sticky: Re: Like Us On Facebook

    Liked
  8. Replies
    158
    Views
    17,852

    Re: Tuning Tutorial

    Found this through a google search:

    http://www.turbo-mopar.com/forums/showthread.php?23646-ABS-sensor-output-for-speed-based-boost
  9. Re: Help me better understand Wategate tables in MPTune

    A 0.035 in. wire feed welder contact tip would work for a restictor. You could find one up locally to you.
  10. Re: proper chip orientation in 87 T 2 Single chip LM zif socket, notch toward hand

    Mine does not have a handle it has a screw. The notch on the chip goes on the side with the screw.
  11. Replies
    12
    Views
    3,377

    Re: 2.5 turbo cutout under load 3-4k rpm

    Connect a fuel pressure gauge to your fuel rail and duck tape it high enough on the windshield so that you or a friend can see it. Go for a ride and watch the gauge.
  12. Replies
    4
    Views
    1,373

    Re: Ignition Problem solved

    Always carry a good known working spare hep in in your car. You never know when they will fail.
  13. Replies
    10
    Views
    1,698

    Re: Fuel pump recommendations

    I have heard of a lot of premature failures with after market fuel pumps. If you want a stock pump, I would go with a factory mopar replacement fuel pump under old part number 5217852 or new part...
  14. Replies
    24
    Views
    4,364

    Re: Turbonator Boost Control T1 or T2?

    What electronic boost controller do you have?
  15. Replies
    297
    Views
    40,654

    Sticky: Re: MPSciLink

    I would gladly pay the extra money for a better quality USA made PCB.
  16. Replies
    297
    Views
    40,654

    Sticky: Re: MPSciLink

    Is the made in the USA board a better quality made board than the China board? Half price for the USA made board in quantity is a good price break.
  17. Replies
    297
    Views
    40,654

    Sticky: Re: MPSciLink

    I am interested in purchasing the final turn key product. Like some others, I do not have the skills to contribute to the development.
  18. Replies
    64
    Views
    9,888

    Re: 1.4l Garrett turbo

    All SRT4's have two resonators right behind the cat.
  19. Replies
    64
    Views
    9,888

    Re: 1.4l Garrett turbo

    Yes, I drove a 1.4T Dart with a stick. The 1.4T in a Dart had no power. I was unable to tell it had a turbo when I floored it in second and third gear. I was not impressed at all.
  20. Re: Where are people getting functioning Supra Turbo PCV valves?

    I have not heard of a similar valve with a 90 deg barb.
  21. Re: Where are people getting functioning Supra Turbo PCV valves?

    Part # for toyota dealer for supra pcv is 12204-46020. It is all metal and will not leak.
  22. Re: car stumbles and runs lean on 1/8 throttle

    Have you checked your fuel pressure? Have you replaced your fuel filter?
  23. End shaft play in rebuilt distributors

    I ordered two reman distributors and they both have excessive end shaft play at .043. My old factory distributor has .011 end shaft play. The upper bushings are worn out in my old distributor...
  24. Replies
    5
    Views
    562

    Suspension Re: ball joint bolt

    Have you checked your local dealership? I bought two of them about two years ago.
  25. Re: 1991 Dodge Spirit R/T 2.5 inch exhaust video

    Do you have a muffler?
Results 1 to 25 of 106
Page 1 of 5 1 2 3 4