Search:

Type: Posts; User: crusty shadow; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    209

    Re: P body window scrapers

    cool this works, should have no issues now.
  2. Replies
    4
    Views
    209

    P body window scrapers

    i just got an 87 csx, scrapers are gone. i know ajakeski was making kits but now does not. anybody know what type of window sweep to use so i can rebuild my own?
  3. Replies
    169
    Views
    23,806

    Re: MegaSquirt Successes Needed

    I ended up using a half-moon style trigger in the original distributor- i cut all the vanes off and cut a piece of i believe it was 2 1/8" exhaust pipe so that i had a half moon style vane and welded...
  4. Re: Flow rate of +40 injectors and 5277895 (TII-TIV injectors)

    if one were inclined to do so you could buy a cheap megasquirt a 12v power supply that can deliver around 30 amps and a 100 cc graduated cylinder, put all that together and you have an injector flow...
  5. Replies
    297
    Views
    39,002

    Sticky: Re: MPSciLink

    Got my kit yesterday, getting ready to assemble it.

    Good lookin board, wish more people did red or colors besides green.
  6. Replies
    258
    Views
    20,500

    Re: MPSciLink starting a Group3 Pre-Order

    ok well if my order hasnt shipped yet i'll take a red board then.
  7. Replies
    258
    Views
    20,500

    Re: MPSciLink starting a Group3 Pre-Order

    It may have already shipped, i placed the order on the 27th, name is Nate Harris
  8. Replies
    258
    Views
    20,500

    Re: MPSciLink starting a Group3 Pre-Order

    I ordered one of the kits, there has been a lot of interest from members of my club in retuning the stock computers lately...
  9. Replies
    3
    Views
    535

    Re: Windshield Wipers (assembly)

    Just as a side note - the wiper arm bushings are still readily available from the dealer- i just got some from the parts department at work last week.
  10. Re: HEP + Megasquirt, someone made it work.

    You can just install a 64-2 wheel, much more accuracy and reliable up to 12,000 rpm.

    with megasquirt the best way to go is run a crank trigger and make a half moon style shutter wheel for the...
  11. Replies
    169
    Views
    23,806

    Re: MegaSquirt Successes Needed

    in order to get the injector dead time measurement, you do a flow test with a graduated cylinder then enter the numbers into an excell spreadsheet, once you get your final dead time and flow numbers...
  12. Replies
    169
    Views
    23,806

    Re: MegaSquirt Successes Needed

    The write up i did was basically how to mount a 36-1 trigger wheel to the crank pulley- looks almost identical to the pic tryingbe posted at the top of this page.
    most of the rest of it is standard...
  13. Re: SEVERE binding on 2-1 downshift after full manual VB mod

    did you do your own valvebodies?
    if so what all did you do to them?
  14. SEVERE binding on 2-1 downshift after full manual VB mod

    wheels try to lock up during 2-1 downshift at any speed, used the superior kit and followed those instructions plus locked shuttle valve, plugged accumulator holes in case and did the valvebody bleed...
  15. Replies
    4
    Views
    825

    413 with 5 clutches in each drum

    getting ready to start assembling my trans, still a bit confused on how i can get 5 clutches in the rear drum. i keep finding conflicting info on here, one post has info on grinding down the thick...
  16. Thread: 85 glh

    by crusty shadow
    Replies
    89
    Views
    22,912

    Re: 85 glh

    Instead of buying high impedance injectors you can grab a set of resistors from a DSM and wire those up with your injectors, you can then keep your existing injectors.
  17. Replies
    10
    Views
    1,814

    Re: 2004 Ram 1500 Front Brakes

    did you go through the abs bleed procedure? you must bleed the abs especially after replacing a master cyl, otherwise you will never get the air out of the system even with a power bleeder.
  18. Replies
    22
    Views
    3,492

    Re: Megasquirt Anyone ??

    One of the benefits of ditching the distributor pickup for the main engine position sensor is you get extremely precise timing control vs using a distributor based pickup. with a distributor based...
  19. Replies
    128
    Views
    26,876

    Re: Development of the Turbo engines

    man that looks a lot like the setup i had in mind for when i plan on going with the big turbo later on down the road. my line of thinking was to use a air to liquid cooler roughly in place of where...
  20. Replies
    128
    Views
    26,876

    Re: Development of the Turbo engines

    " out of nowhere a wild Chrysler powertrain engineer appears!"
    Gotta say im really enjoying this so far. I have so many questions, as do others im sure. your finger are going to take a beating...
  21. Replies
    39
    Views
    6,219

    Re: T1 PCV valve function

    i agree with this, with everything you say you've done it could be excessive blow-by getting past the rings and pressurizing the crank case and forcing oil past the pcv valve.
    disconnect the pcv...
  22. Replies
    39
    Views
    6,219

    Re: T1 PCV valve function

    The PCV valve is a metered vacuum leak, it's not supposed to close off completely.

    Did you follow the instructions in the factory TSB about resealing the baffle in the valve cover?
  23. Replies
    39
    Views
    6,219

    Re: T1 PCV valve function

    Cut the extra tube off a TBI cover, drill an appropriate hole in the turbo cover, take it to a welding shop and have the tube welded to the turbo cover. This also gives you an excuse to strip and...
  24. Replies
    39
    Views
    6,219

    Re: T1 PCV valve function

    The permanent fix for this is to add a second tube in the valve cover for the PCV valve, use a short 90 degree elbow to mount the PCV valve straight up and then run the hose to the vacuum port on the...
  25. Replies
    22
    Views
    3,492

    Re: Megasquirt Anyone ??

    don't be too sure about that :thumb:

    The way i have mine set up is i run a 36-1 crank trigger and a half-moon aka "polling" shutter wheel on the distributor. On that setup the MS doesnt use the...
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4