Search:

Type: Posts; User: bfarroo; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    3,268

    Re: J&S Electronics Knock Control

    I have a flashable computer that will end up going in the car. I’m thinking it can’t hurt to leave it in. The car spent over 8000 miles on the track with the current setup so I’m guessing it’s...
  2. Replies
    3
    Views
    3,268

    J&S Electronics Knock Control

    My car has a J&S knock control module installed on it to supplement the Super 60 computer. It has everything needed to support the super 60 computer and made a little over 300hp on 18 psi. Anyone...
  3. Replies
    4
    Views
    10,058

    Re: Who is this?? 88 car seen on track

    Intercooler is mounted up in the scoop instead of in the side behind the door.
  4. Replies
    4
    Views
    10,058

    Re: Who is this?? 88 car seen on track

    That’s Andy’s car. He use to have mikes blue 16valve car. Now has this race car.
  5. Thread: Electric GTP

    by bfarroo
    Replies
    12
    Views
    27,433

    Electric GTP

    Spotted in Texas

    http://www.turbo-mopar.com/forums/photopost/data/1017/UWRQ2452.JPG
    http://www.turbo-mopar.com/forums/photopost/data/1017/WPIT5575.JPG...
  6. Replies
    235
    Views
    68,525

    Re: Finally Starting on #53

    Wow it's been a year since I've updated this. Built a new house so it wasn't until this winter I got the car into the new garage. I have all of the gauges now and wiring them up in the dash. I...
  7. Replies
    27
    Views
    54,042

    Re: Another 2.2 vs. 2.5 debate

    I vote 2.5 all day every day for a street driven car that is relatively stock. The low end of the 2.5 is just way more drivable and fun compared to a 2.2. With the availability of people that can...
  8. Replies
    13
    Views
    3,383

    Re: Red 16V TC Masi runs clean AF!

    That's some dumb stuff there. In WI you just don't renew if you're not going to use the vehicle. When you decide to drive it you just go back in and register. Most of my cars if I'm going to keep it...
  9. Replies
    235
    Views
    68,525

    Re: Finally Starting on #53

    Honestly I feel like I'm getting close to the end of the tunnel. I have half the gauges ordered, just need to get the rest and install the dash, then get the fuel tank and I should be able to start...
  10. Replies
    235
    Views
    68,525

    Re: Finally Starting on #53

    Squared up my fiberglass sheets and installed my cleaned up and painted cruise actuator. Just need to measure out what size I need and cut it to the proper size.
    ...
  11. Replies
    235
    Views
    68,525

    Re: Finally Starting on #53

    Got a windshield wiper and laid out some fiberglass sheets to make the lower covers for the front and rear.

    http://www.turbo-mopar.com/forums/photopost/data/1002/medium/IMG_3315.JPG
    ...
  12. Replies
    235
    Views
    68,525

    Re: Finally Starting on #53

    What are the issues any other GTP owners have had with the speed sensor? I've heard of owners switching to the gps style sensor. I'm looking at gauges for my car and I don't see anything that matches...
  13. Re: 88 Daytona Dash Cluster Wiring Diagram Needed

    Got what I needed

    http://www.turbo-mopar.com/forums/photopost/data/1002/medium/Red_Plug.JPG

    http://www.turbo-mopar.com/forums/photopost/data/1002/medium/Grey_Plug.JPG
  14. Replies
    235
    Views
    68,525

    Re: Finally Starting on #53

    Looking for a passengers side outer or drivers side inner headlight if anyone picked up any extra from rosin. I wasn't paying attention when I was grabbing them and I grabbed two drivers side outer...
  15. Replies
    235
    Views
    68,525

    Re: Finally Starting on #53

    Here they are from a FSM incase anyone else needs them. Thanks Mike Pascali for looking them up.

    http://www.turbo-mopar.com/forums/photopost/data/1002/medium/Red_Plug.JPG
    ...
  16. 88 Daytona Dash Cluster Wiring Diagram Needed

    I'm looking for a wiring diagram for the dash cluster for a 88 daytona or similar model car. I need to determine what pins I need to tie into for the indicators for my consulier dash. Any help...
  17. Replies
    235
    Views
    68,525

    Re: Finally Starting on #53

    Any of you found a wiring diagram for the dash wiring? I need to start locating the wires to hook up the indicators on the dash and haven't had any luck yet finding anything. I'm guessing it's an 88...
  18. Replies
    235
    Views
    68,525

    Re: Finally Starting on #53

    Started fitting the rear spoiler I picked up at Rosin. I got the rear cut down to the correct length to line up with the rear grills. Just need to lengthen the front to cover the radiator and blend...
  19. Replies
    235
    Views
    68,525

    Re: Finally Starting on #53

    My ball and socket came in for the end of the prop rod but I somehow ordered a left hand thread instead of a right hand. Not sure how I managed that but I have the correct one on order now.
  20. Replies
    235
    Views
    68,525

    Re: Finally Starting on #53

    Got the engine cover rod mount made. One small step closer.

    http://www.turbo-mopar.com/forums/photopost/data/1002/medium/IMG_3219.JPG
    ...
  21. Replies
    235
    Views
    68,525

    Re: Finally Starting on #53

    Rear side marker lights came in. Should be able to get them mounted and wired this weekend. Moving forward 1 small step at a time.
    ...
  22. Replies
    9
    Views
    5,765

    For Sale Re: Consulier GTP for sale

    That's went out of my price range quick. Doubled in two hours.
  23. Replies
    22
    Views
    6,745

    Re: GTP up for auction on BAT

    The electric car looks like a roadster like mine. If you look at the pics close it doesn't have the same profile and the targa hoop. it's much more slim and doesn't have support for a window.
  24. Replies
    235
    Views
    68,525

    Re: Finally Starting on #53

    Thanks Johnny. The car actually has two nutserts right there so I'm all set. Jut cut some angle and get a ball and socket setup.
  25. Replies
    235
    Views
    68,525

    Re: Finally Starting on #53

    The body is physically molded for the square rear lights. Maybe they put the extra body panel over the square light recess when they used the long one? The front isn't molded for anything and I...
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4