Search:

Type: Posts; User: chromguy; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    6
    Views
    61

    Re: ideas on long term MTX storage

    OK I can see that working well.
  2. Positive Jeff1234 is great seller with excellent communication

    Jeff1234 is great seller with excellent communication
  3. Replies
    18
    Views
    1,996

    Re: Rust protection

    Here is one of the product I use with a standard Schutz type pneumatic undercoating sprayer
    http://ca.proformproducts.com/en/products/coatings/rustproofing/dripless-oil-annual-rustproofing/
    Here is...
  4. Replies
    6
    Views
    61

    ideas on long term MTX storage

    I am looking for ideas for long term MTX storage. Currently they are in my unheated garage. My current procedure is to place 1.75" plugs sealed with RTV in the diff axle seals and overfill with 10W30...
  5. Replies
    22
    Views
    1,369

    Re: Omni with 2.2 turbo engine codes woes

    https://drive.google.com/open?id=1eRUt8JZea226V8fJNM6EvgL8gWAZ5uRp
  6. Replies
    22
    Views
    1,369

    Re: Omni with 2.2 turbo engine codes woes

    I have connectors index on the SBEC 60 way. IE Map=1 Cool=2 Battery=3 Sensor ground=4 Ign=9 ground =11-12 25 =Tx and 45=Rx for example
    Is this what you are looking for?
    I also have this in a...
  7. Re: SBEC Electronic schematic/flowchart/logic diagrams

    reverse engineering is difficult and slow for everybody. When you find info please share.
  8. Re: SBEC Electronic schematic/flowchart/logic diagrams

    I have pseudo schematics for the 87 LM which will give you an idea of what goes on in the SBEC.
    https://drive.google.com/open?id=0B3qZZUQ9qnBldFlnampwazNzYXM

    I have Reversed Engineered the...
  9. Replies
    18
    Views
    950

    Re: Sci/FTDI cable issues

    Good catch Dan
  10. Replies
    18
    Views
    950

    Re: Sci/FTDI cable issues

    If you have the ability to solder, I would recommend to reflow the solder on the pins, Including the Rx,Tx and ground pins of the SCI connector as several are not soldered on both side. This may or...
  11. Replies
    18
    Views
    950

    Re: Sci/FTDI cable issues

    Send us a picture of both sides of the board, it could be an assembly issue.
  12. Replies
    8
    Views
    452

    Re: SBEC injector drivers

    Dan,
    Last night I checked the MOSFET requirement for speeduino that only works as is for high impedance injectors, they use a STP25N504Z that is rated for 80A ....They don't recommend you use low...
  13. Replies
    22
    Views
    1,612

    Re: Woosh from brake booster

    I decided to test on my Sundance DD as the cooling system crackles after driving and I can hear things boil slightly.
    Now the problem...
    This product caused my rad fan to stop working even on an 85...
  14. Replies
    8
    Views
    452

    Re: SBEC injector drivers

    Dan,
    i test a few SBEC and SBEC2 drivers in circuit with my transistor tester but no luck. I guess I need to unsolder them to fully characterize.
  15. Replies
    8
    Views
    452

    Re: SBEC injector drivers

    Low vs high impedance???? I have no idea what is type A or B.. google search was of no help either
  16. Replies
    2
    Views
    239

    Re: MPTUNE - Rich idle/part throttle HELP

    What I have done in the past is lower the injector size reported in MPTune by small amount (10% to let say 65lb).
  17. Replies
    27
    Views
    3,954

    Re: Cam Numbers/Roller Rockers

    Woops!
  18. Thread: Lizard Skin

    by chromguy
    Replies
    12
    Views
    3,260

    Re: Lizard Skin

    .
    I live in the salt belt. My car in the picture is 32 years old and my DD.
    http://www.turbo-mopar.com/forums/showthread.php?84332-Can-t-install-LSD-in-A555&p=1148367&viewfull=1#post1148367...
  19. Replies
    8
    Views
    452

    Re: SBEC injector drivers

    Hi Dan,
    I checked a SBEC2 that I have hacked and three that I could read have a PH4947 but I could not find any info on them. Perhaps a special Cryco part number and one also had a Chrysler part...
  20. Replies
    8
    Views
    452

    Re: SBEC injector drivers

    Hi Dan,
    I can have a look tonight to see if I can cross-reference.
    My guess is C as the injectors are approx 2 ohm and thus 14/2 = 7 amp albeit for a short period of time
  21. Re: Colour code for SBEC2 driver alignment assemblies

    Interesting that I just found a SBEC2 with the same combo as the Turbo but without several of the MOSFET drivers installed.
    Rats, now things are more complex, what a shocker!!!
  22. Replies
    10
    Views
    567

    Re: replacing vacuum lines

    ais site:www.turbo-mopar.com in google the colon tells google to only search "ais" on the web site after the colon

    here is the link using DuckDuckGo...
  23. Re: Colour code for SBEC2 driver alignment assemblies

    Thanks Brian,
    I will write up with picture what I need over the next day or so
  24. Colour code for SBEC2 driver alignment assemblies

    Anyone with information on the colour code of the plastic clip that is used to push the MOSFET drivers in contact with the heatsink. I have seen Red, Green, Yellow, Black, Gray, Blue, Orange,...
  25. Replies
    0
    Views
    176

    SBEC2 PCB part numbers

    We are looking for part numbers of PCB boards of SBEC2 so far I have found
    463-2377 I have only found these with T1 and TIII configurations.

    451-7652 I have multiple V6 versions such as 3.0...
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4