Search:

Type: Posts; User: jpcturbo; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    29
    Views
    997

    Re: More on calculated tables question

    I'll see if I can get some logs by this weekend. Else the window of opportunity to get out there and make some runs has pretty much closed until spring.

    Jeff Chojnacki
    '87 LeBaron 2.2 T2 Auto...
  2. Replies
    29
    Views
    997

    Re: More on calculated tables question

    Morris, if you want some logs from a LM, not SMEC, turbonator cal I may able to do it this Saturday.

    Jeff Chojnacki
    '87 LeBaron 2.2 T2 Auto
    '88 Caravan 2.2 T2 5spd
  3. Replies
    18
    Views
    1,794

    Re: Sci/FTDI cable issues

    Never experienced this idle increase with a SMEC. I do see this regularly on my LM k-car.
  4. Replies
    2
    Views
    685

    Re: MPTUNE - Rich idle/part throttle HELP

    If your FuelBaselineFromMap and PartThrottle tables are not just off, then perhaps try working with the Battery Offset table. ...
  5. Replies
    26
    Views
    5,104

    Re: 1988 LeBaron 4 dr 2.5 TBI

    The Turbo pump should be fine as the regulator sets pressure and the return line is the same as on the turbo cars?

    If you pull the tank, I'd imagine setting up something on the jack to keep the...
  6. Replies
    26
    Views
    5,259

    Re: Official SDAC-29 Discussion Thread

    I think all the cars should enter the show regardless of condition. They all have some story to tell.
    My Le-Baron needs lots of cosmetic work but I'll still enter it this year. It's last SDAC was...
  7. Replies
    18
    Views
    2,487

    Re: abrupt momentary shut off of engine

    Yes. The number is the psi where over boost cutout starts. So if you set it for 13psi then overboost will happen at 13psi. I'm not sure which LM cal version your working with but it probably is under...
  8. Replies
    18
    Views
    2,487

    Re: abrupt momentary shut off of engine

    You can raise the limit. There should be a section in the cal about overboost. Look at the values and in the description should help tell you which one to change. Set it to a psi value well before...
  9. Replies
    18
    Views
    2,487

    Re: abrupt momentary shut off of engine

    The ball in the grainger faces the side that is connected to the vacuum. The spring side is connected to the wastegate (and ideally a small vent). That way boost pressure pushes the ball that...
  10. Replies
    18
    Views
    2,487

    Re: abrupt momentary shut off of engine

    Not sure what kind of boost controller but, Yes, you are correct having the laptop connected to the Ostrich makes no difference as the program is on the Ostrich.
  11. Replies
    38
    Views
    3,628

    Re: 1987 csx stumble

    Good excuse to go through all the engine grounds and check for a loose or corroded wire?

    Jeff
  12. Replies
    258
    Views
    23,533

    Re: MPSciLink starting a Group3 Pre-Order

    I'd like one as well. Thanks!
  13. Replies
    77
    Views
    8,345

    Re: mptune / mpscan update

    First time I started MPTuner (2.0.5.0) this year, was last weekend, so I missed the remote storage migration upgrade window. Can I update the "Program ULR Update Address" manually? and if so what is...
  14. Replies
    69
    Views
    25,253

    Re: SDAC 26, Friday June 24th Getogether

    Sorry! Forgot I don't have a signature on here.

    Jeff Chojnacki
  15. Thread: MPTuner

    by jpcturbo
    Replies
    1,306
    Views
    150,328

    Sticky: Re: MPTuner

    Using MPTune 2.0.5.0. When looking at the FullThrottleTotalTiming Calculated Table, it seems is treating the LimitForHotMAPAdvance (RPMLMT) table as a minimum value for MAP calculated timing instead...
  16. Replies
    69
    Views
    25,253

    Re: SDAC 26, Friday June 24th Getogether

    I should be there in the early evening!
  17. Re: Anyone using a SMEC with the 0-1V output from a wideband?

    I'm using the LC-1's narrow band (0-1V) output to the SMEC with a T-SMEC 16.9 calibration in my Turbo Van. Runs great. Gas mileage is Ok I think. It's been setup that way for a few years but lately...
  18. Thread: Sdac 24?

    by jpcturbo
    Replies
    383
    Views
    46,778

    Re: Sdac 24?

    :amen:
  19. Re: cuts out @ 4600 rpm, I'm thinking its the LM

    You should try a stock cal or the MP stage 2 if you can. I know Rob is very good and this is a long shot but if either one of the cals still cuts out then you have pretty much eliminated the LM as a...
  20. Replies
    232
    Views
    23,434

    Re: Logworks plugin for SMEC/SBEC/LM

    If I remember right it seems as a "Feature" logworks3 tries to configure the number of channels automatically from what it sees on the chain upon connection. Obviously it's not working in our...
  21. Replies
    232
    Views
    23,434

    Re: Logworks plugin for SMEC/SBEC/LM

    One value obviously worked fine. Two had some issues. LMLog and SMECLog both throw out the first two Rx chars after sending an address request. I always wondered if Geoff or anyone figured out a...
  22. Replies
    6
    Views
    435

    Re: lm logging trouble

    Sorry for cutting out on the conversation. I got pretty sick last week. Glad to see you guys got it working!

    Chem was always my datalogging reference program.
  23. Replies
    6
    Views
    435

    Re: lm logging trouble

    The message means it can't talk to the Logic Module. It's trying to say, Hey LM why don't you kick up the communication speed so we can get some logging going on? Since there is no response or the...
  24. Replies
    79
    Views
    5,348

    Re: Logworks plugin for logic modules

    I ran the latest driver on the minivan and got no Dll errors but No Auto ID. This was done on the regular COM1 though one of Chad C's serial converters. I was going to try the old '89 baudmod cal...
  25. Replies
    79
    Views
    5,348

    Re: Logworks plugin for logic modules

    When your at point you can do it, yes that would be great.
Results 1 to 25 of 52
Page 1 of 3 1 2 3