Search:

Type: Posts; User: RayO; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    1,848

    Re: Crossover shaft oil seal

    Here's a trick to help you replace the top plate, to make sure the three lugs stay lined up when you have no room to easily maneuver, i.e., when the transmission is still in the car. Wipe the...
  2. Replies
    12
    Views
    1,848

    Re: Crossover shaft oil seal

    Correction of a possible misunderstanding. By "top cap" I meant the plate affixed with six bolts, not the vent. Oil is seeping out of the interface there, not the vent cap, and I'll have to remove...
  3. Replies
    12
    Views
    1,848

    Re: Crossover shaft oil seal

    Got new seal on crossover shaft. Still a bit of seepage under top cap. Off it comes. Fun in the cold.

    ...........R
  4. Replies
    12
    Views
    1,848

    Re: Crossover shaft oil seal

    Today is 7 Jan 2018. This is a test to see if I get the Forbidden message.

    .........Ray

    - - - Updated - - -

    Back to the original thread...we hope.

    [PART 1 of 4] To verify the leak is...
  5. Replies
    12
    Views
    1,848

    Re: Crossover shaft oil seal

    Can't reply. FORBIDDEN! Fix this please, forum monitors.
  6. Replies
    12
    Views
    1,848

    Re: Crossover shaft oil seal

    This forum is buggered!

    - - - Updated - - -

    NOTHING WORKS HERE. What gives??
  7. Replies
    12
    Views
    1,848

    Re: Crossover shaft oil seal

    Hey, 135sohc!! Just the guy I was hoping for. I saw your search back in 2011 and if anyone knew where to get these, it'd be you.

    Did you have pooling of oil in the top cavity of the gearbox? Did...
  8. Replies
    12
    Views
    1,848

    Crossover shaft oil seal

    Hi, guys,

    I need a crossover shaft oil seal, part no. 4446285. Dimensions 7/8" OD, 1/2" ID, and 1/4" thick.

    My 5-speed manual transmission is leaking BADLY, oil pooling into the cavity on top,...
  9. Replies
    4
    Views
    808

    Re: Short Circuit Glove-Box Light

    Miles, if you mean the shop service manuals, I have them. I just installed a 5-speed manual into my LeBaron LE and the job is impossible without the full service manuals, mechanical, electric wiring,...
  10. Replies
    4
    Views
    808

    Re: Short Circuit Glove-Box Light

    Chromguy, et al, Please note that fuses may LOOK good but are NOT when checked for continuity.

    Problem solved. Sorry to take up bandwidth.

    .......Ray
  11. Replies
    4
    Views
    808

    Short Circuit Glove-Box Light

    AA body, LeBaron LE. Installing LED into glove box required reversing the leads. This caused a short when I reinstalled the socket and now the dome & map lights don't work, nor does the radio. All...
  12. Replies
    9
    Views
    1,569

    Re: Clutch Won't Release

    Barry, thanks. Well, glad I'm not the only one who's discovered the clutch can go too far..


    Joe, as you may know I have two A543 five-speed transmissions. The first was full of problems...
  13. Replies
    9
    Views
    1,569

    Re: Clutch Won't Release

    PROBLEM SOLVED!
    Clutch fully functional.

    It was in fact overpushing the clutch-spring fingers and binding the disk.

    ............R
  14. Replies
    9
    Views
    1,569

    Re: Clutch Won't Release

    Well, now, 83scamp hit the nail on the head. Stupid me didn't test the clutch lever for position before hooking up the cable, and at first hookup the clutch was in fact released. Pushing on it...
  15. Replies
    9
    Views
    1,569

    Re: Clutch Won't Release

    After grinding away on this in my head for over a day I think you're right. I'll check it today. It's the only thing that makes any sense.

    Rob (Shadow), I'm sure I didn't get the throwout fork in...
  16. Replies
    9
    Views
    1,569

    Clutch Won't Release

    Gentlemen.

    Here's the data.
    New Luk flywheel
    New Luk clutch kit with new throwout bearing.
    New clutch cable with 4377825 Isolator
    Trans is A543 into V-6

    This is a swapout...
  17. Replies
    25
    Views
    3,172

    Re: BOBBLE STRUT on LeBaron LE

    Johny,

    Thanks for your comments, but I have to take issue with 'em. Elementary physics tells us as a mass rotates or tries to rotate about an axis (the axles) there will be motion both upward...
  18. Replies
    25
    Views
    3,172

    Re: BOBBLE STRUT on LeBaron LE

    Joe, thanks for the comments. I finally found this on page two, hence the delay in my response. I gave this problem lots of thought over the six months it's taken me to change from automatic to...
  19. Thread: PHOTO of 4377825

    by RayO
    Replies
    28
    Views
    3,237

    Re: PHOTO of 4377825

    Marty, I'll take one. Will contact you via private message. Thanks.

    ......Ray

    Edit: Private msg sent 2:40 p.m. Wednesday, mountain time.
  20. Thread: PHOTO of 4377825

    by RayO
    Replies
    28
    Views
    3,237

    Re: PHOTO of 4377825

    Thanks, cordes.
  21. Thread: PHOTO of 4377825

    by RayO
    Replies
    28
    Views
    3,237

    Re: PHOTO of 4377825

    Krut & Chris & Randy: I got Randy's pic via email. I see the same image above here on his third try. I spoke with Chris today on the phone and no, Krut, there's no poly part available. He thought I...
  22. Thread: PHOTO of 4377825

    by RayO
    Replies
    28
    Views
    3,237

    Re: PHOTO of 4377825

    Randy, your 3rd attempt worked; however, I've seen that drawing before. It doesn't help. What's it made of? BTW, I can't see your image 61484.
    Don't feel bad about no computer expertise. I've used...
  23. Thread: PHOTO of 4377825

    by RayO
    Replies
    28
    Views
    3,237

    Re: PHOTO of 4377825

    Randy, can you tell me what the part is made of ? Steel? Plastic? Rubber? Thanks.

    ...........R

    - - - Updated - - -

    Actually what I also need to know is how high it makes the rubber end of...
  24. Thread: PHOTO of 4377825

    by RayO
    Replies
    28
    Views
    3,237

    Re: PHOTO of 4377825

    Randy, still no good. I notified the administrator. Thanks for your kind efforts.

    ..........Ray
  25. Thread: PHOTO of 4377825

    by RayO
    Replies
    28
    Views
    3,237

    Re: PHOTO of 4377825

    GLHS60, When I click your link I get "Invalid Attachment specified....."

    Do I need to do something to see it? Duh.

    ........R
Results 1 to 25 of 83
Page 1 of 4 1 2 3 4