Dont know too much about the transmission options. Im assuming there is no quick fix for this.
I shift into 2nd and it grinds started all of a sudden.
What are my options here.
- Just get the...
Type: Posts; User: kleiner; Keyword(s):
Dont know too much about the transmission options. Im assuming there is no quick fix for this.
I shift into 2nd and it grinds started all of a sudden.
What are my options here.
- Just get the...
Fuel pressure is good. 40 psi at idle and looks to go up as I am on the gas. Fuel Filter i have not changed in a few years. but figured it was not this as it only seems to happen in the same spot. I...
86 omni glhs. 87 lm module with custom cals.
Symptoms. The car starts fine, idles fine and anything over 1/8 throttle and car runs great. But it is when I shift out of first into second or even...
Omni's rock.
I have one and I am debating an intake setup as the one Speidz has. I currently have the air filter right under the pipe from the intercoller to the throttle body. the probelm with this...
Thanks for the quick reply
If they are not torque to yield bolts I will re-torque them. If they are I will leave them alone.
Can anyone shed some light on this for me. 11mm ES72723
I found this
...
Sweet,
thanks Rrider.
looks like I am gonna try 6's because I have them and I could race this weekend. Looking to mount them in a few days.
Unless I can get some good info why this is a bad idea.
13's sec would be great. Possibly 12's later.
Got some used slicks and I need to put them on some rims.
MT says 8 inch,
- I have 6 inch around will this suffice? or do I need at least 7 inch.
When I put them on do they need to be balanced? if...
-Ya I got the code, they were made 28th week of 2009,
- Mt's webstie says that anything over 4 years old should be replaced. But I think for what I need them for they will be fine.
- - - Updated...
Good info,
Thanks and yep no cat :thumb:
Found this
http://www.turbo-mopar.com/forums/showthread.php?48863-Seafoam-vs-Water&highlight=water+seafoam
So how exactly should I go about doing this on our cars?
Turbo 2, 2.2.
Warm up the car first then
- Spray a fine mist into the TB with the engine between 3000 and 3500
or
- use a vac line to...
Ok I will check them over (wear marks and sidewalls) What am I looking for in the sidewalls cracks? or tires not stored right will have bends in them?. But I probably will not use them often, as I...
Thanks, that helps,
Would me offering 150 for them be fair???
I found these that I may purchase,
says he bought them in 2010.
What do you think they are worth? Just the tires, no rims.
I havent seen them yet, what should I look for?
These will be my first...
Good idea to use a calculater. Right now I have minimal play on the inside, so the room needs to go to the outside. After using the calculator you are right I need more like an et of 25. This will...
Did the 15x8 fit?
I was trying to figure out how to do this last spring. Blew a head gasket and now I finally have the car back together and am looking again. thanks for the pics and info dart165.
Judging from that...
It is a TBI it is a 94 acclaim. And -23 is never around here.
So I can bypass this. Is there a way to fix it when I get a chance or do I need a new manifold?
Is the coolant nipple on the manifold...
It barely ever gets below 10 degrees celcius here. So can i just bypass it? Thanks for the help
Is it possible to fix this? like jb weld or something? or do I need a new intake? does the intake need coolant in it? or can I bypass this?
thanks for all the help
Took the both to a machine shop and went with the crossdrilled one, it was ok.
Cheers
From what I have read it doesn't really matter