Check the turbo for excessive play & inspect it for wheel to housing contact, though you'd probably hear that. Also check exhaust for restriction after turbo (maybe take pipe loose before the...
Type: Posts; User: A_ Kelley; Keyword(s):
Check the turbo for excessive play & inspect it for wheel to housing contact, though you'd probably hear that. Also check exhaust for restriction after turbo (maybe take pipe loose before the...
https://drive.google.com/file/d/1A4m9GjL2K1X_dflnbeaHvwKt-vbhviOa/view?usp=drivesdk
356 cal reverse assembled and mostly identified.. for those interested. No template file yet.
I got one but it'll be tomorrow or next day before I can pull it up. Email it to you if you pm me your email address.
Check connector at the computer.. might be connector pins losing contact.. my Jeep is the Ignition switch it turns out. (Flaky contacts in switch, still turned over but wouldn't hit until the key is...
Oddly enough, my Jeep Cherokee is doing the same thing. Unfortunately my engine light burned out and haven't replaced it yet, but it's getting power to the pcm but seems like it's flooding trying to...
So much good stuff said here... This forum needs a like button for posts!
What year make models, motors do you need? Then I'll look them up and dump them into a PDF onto my goopgle drive and pm you the link.
I can get you the diagrams from Mitchell, not sure if it'll have a pinout like the jeep fsms do, but it'll have all the ecm wiring on one or two pages.
Sure you would have to but that would be simple enough.. just make a bracket that comes off the valve cover bolts or off the block somewhere. Likely not worthwhile unless you are having trouble...
Umm.. rethink that a moment.. the rotor and cap is a rotary switch essentially. It does not affect timing more than a few picoseconds as long as the rotor is pointed at the terminal within several...
I'd have to look at the pin out of the Jeep ECM to see if it would work with the TM stuff.. I think some pins would be different. (Jeep lacks baro read solenoid and some other little stuff that may...
Yes there's lots of dodgy remarked chips on the Chinese market. Be careful. There are other sbec with a 27c256 that can be moded to take another EEPROM with minimal work. (At least Jeep ECM were set...
You could order a BB board from oshpark and assemble it, just saying.. then no uv erase or removal..
no you can't base the cam signal off of the crankshaft because it rotates at half the speed of the crank and cannot differentiate between TDC on 1/3 vs 4/2. the portion of the cam sensor that...
It should be easy to make a encoder for the crank, and then make a encoder for the cam.. you'd need to keep the cam sensor to determine which injectors to fire (sequential).. if you don't, it'd still...
It should be possible to make a trigger wheel to create a HEP signal.. I say that but i haven't seen a HEP encoder wheel. Still would need a sensor/encoder on the cam though for injection if it's...
If there were a common site to store project code on, a simple Todo list in a text file would work to set goals and as information in relating to it... I'm sure there are more advanced source control...
Not quite a 4.0 missing 2 cylinders. It's actually the same 2.5 as used in some Dakota trucks.
Oh that's way more advanced than I was shooting for on the Jeep... I was mainly going to do something in the ECU similar to early models where it was an across the board retard until throttle let...
IDK it's probably able to be converted to smec or the 3.0. just need to know what kind of signals it uses for ckp/cmp. The generation code is fairly easy to reconfigure as it is based internally off...
In the future I'm looking into adding a knock sensor to the Jeep Cal, by using an extra input to sense knock..
No I was working on a cal for a 356 but code is nearly identical, just locations changed a little bit and it uses the o2
Interesting fact: the 356 cal has a config switch for 4/6 cylinder in code.
- - - Updated - - -
I'd possibly be interested in taking up mp suite but will it compile on .net 2003? I don't think I've got access to anything newer or a computer capable of running it. (I'm...
I'm in for coding/hardware development/sharing knowledge of the internal workings and protocols on the SBEC.
I couldn't get mptune to work with my USB to serial adapter and I'd love to try mpscan but I don't want to upgrade .NET. maybe I will on my laptop but my desktop didn't even have any .NET which is...