The automatic seatbelt thing was 94-95 model year thing to get around the lack of a passenger side air bag.
Looks like the P and A body used the same shift cable for the floor mount....
Type: Posts; User: 135sohc; Keyword(s):
The automatic seatbelt thing was 94-95 model year thing to get around the lack of a passenger side air bag.
Looks like the P and A body used the same shift cable for the floor mount....
Find an earlier year and swap everything over. It all fits right in, you will need to make a nut plate for the top of the "B" pillar seat where the seat belt attaches.
On that same doner car if...
The compressor in 1994 will be a Denso 10PA17C
DENSO p/n 4710265 is the same compressor assembled with a slightly larger (1/8 inch diameter) clutch pulley for the second generation LH cars. The...
Years ago one could get .001 inch/.025 mm undersized bearings which were great for a typical 150 thousand mile engine that was not 'worn out' but just outside of the standard sizes after cleaning up...
I looked that up, sounds like good stuff but I wonder about the cold weather performance ?
That stuff seems to have a love it or hate it following here. To hear you endorse it I will take...
Interested to hear what others have been using/concocting in our manual transmissions as 5w20 and 5w30 conventional flavor oils are being phased out.
I have tried everything over the years and...
A minivan going fast enough to need a roll bar. Never imagined the day would come :)
Yup :thumb:
Polyolefin based.
https://www.polyvance.com/identify.php I use often.
The early T1 air box is probably ABS.
Step file ?
The large part would be a four op setup with the cross drilling and end threaded hole, the small one could be done in two.
I would add a helicoil insert to the threaded hole and a...
Side-side motion control. It keeps the axle centered underneath the car.
Other than sticking with an OEM name brand like Valeo, Sachs or LUK it will be a roll of the dice.
The aftermarket as the demand for these parts has shrunken has likewise consolidated coverage...
If you remove the dashboard there might be enough wiggle room at the expansion valve to hose connections to unbolt the heater box from the firewall and pull it back a couple inches to take the top...
I was hoping you would chime in. Other than a few junkyard engines robbing parts from when these cars were still showing up at the yards I have never seen that style of adjuster in widespread usage....
When you do the transmission seal make sure you don't lose the shim and plenty of rtv on the seal retainer and the three bolts.
https://polybushings.com/pages/altIsolator.html
Common bell-housing meaning they all look like that (greasy, oily mess) when they get a few miles on them. The rear main seal does not take much to leak and combined with the clutch dust it turns...
Ed Papp/Onerippinturbo2 would probably scoop up a lot of that stuff but he has not been on since early march.
The 89+ style.
You might know better but I do think the break between years is of course 87-88 (headlights obviously) 89-90 and 91+ due to the radiator/core support changing because of the hood...
Looking for a Passenger side fender, hood, Shadow or Sundance grille, charcoal canister, front bumper both the inner steel crash bumper and the outer cosmetic cover. One or both bumper shock...
The location of the tie rod hole is different. Simon/TurboVanMan I think posted a picture some time ago showing the difference.
If melting stuff is becoming a problem you could always go to the Denso style starter.
Denso starter
The connections are on the side, nearly at the bottom vs the Bosch unit where they are...
I cannot speak for anyone else but if I was getting serious enough to spend $2k+ on a set of axles they need to be rebuildable.
Something like this is what I would have in mind to get away from the junk store replacement axles.
https://www.kustom1warehouse.net/All_new_IRS_axles_with_cv_joints_p/irsaxlescomplete.htm
It...
The proliferation of cheap, offshore cv axles has effectively killed the aftermarket for service parts. Look as DSS axles, they were just another middle man buying the semi finished components from...