Search:

Type: Posts; User: supercrackerbox; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    15
    Views
    3,249

    Re: bench testing heater and AC cores

    The copper ones seem much more durable and seem to last longer than the aluminum ones.

    Now my question is, if you find a small leak in a bench test like yours, can you braze or sweat the leak to...
  2. Replies
    25
    Views
    4,055

    Re: Cooling issues

    The potential issues with that are A: The steel plug is completely seized into the head, or B: Many heads I've seen don't even have the hole. While it's easy enough to drill and tap, novices may be...
  3. Replies
    10
    Views
    4,303

    Re: Full three inch exhaust on L body.

    I can't speak for having a bigger turbo, but I can say that the spool up was noticeably better on my Charger with a full-length 3" with muffler vs. my CSX-T which had a 2.5" side dump and no muffler....
  4. Replies
    10
    Views
    4,303

    Re: Full three inch exhaust on L body.

    Like Mike said, it's really tight but it's a very nice system. One thing I did change on my Charger was to take a couple of 22 scrap bends I got from work and made an offset to give a little more...
  5. Replies
    6
    Views
    996

    Re: Rear wheel bearing issues

    Okay, so what I found today is that both Set39 and Set46 bearings use the same outer cup JL26710. So my only guess is maybe the I.D. of the cone is different. I haven't found specs for the Set46...
  6. Replies
    6
    Views
    996

    Re: Rear wheel bearing issues

    Both hubs were taken from a '91 LeBaron GTC along with everything else to do the big brakes on the '89 ES. Both of the races I removed say Koyo LM12711; both of the new bearings are Timken LM12711...
  7. Replies
    6
    Views
    996

    Rear wheel bearing issues

    I'm trying to install a big brake package on my kid's Daytona ES. I'm getting two different options for the rear inner bearings, a SET46 or a SET39. Is it just a situation where I have to match up...
  8. Re: 1987 New Yorker MAP Sensor Location

    Didn't they start putting it under the hood in '87?

    If your LM has a little black plastic cover on it, you'll either have two wires coming out of it, or a black plastic vacuum tube. If it's the...
  9. Replies
    9
    Views
    3,450

    Re: Decent price for chrysler laser?

    There should be a little black switch in the glove box to turn the voice notification on or off if I remember correctly.
  10. Replies
    6
    Views
    1,080

    Electronics Re: Descriptive Title

    That sounds like how my '91s work, except they have the push button headlamp switches. It was a nice feature to have when I'd come home at night; the headlights would stay on long enough for me to...
  11. Replies
    8
    Views
    1,237

    Re: 91 shadow 5M, what trans?

    I didn't know the Shadow was available with the High Torque option; I thought it was only Daytonas and LeBarons.
  12. Replies
    6
    Views
    1,080

    Electronics Re: Descriptive Title

    I never realized the time delay ones were available before 1991.
  13. Engine Re: Spirit/Daytona R/T Airbox and Snorkel

    Parts have been sold.
  14. Replies
    22
    Views
    6,460

    Re: Rust protection

    What am I doing wrong with the Fluid Film? I've tried it extensively on my truck and my '91 Daytona. It didn't do anything to protect them, and washed off just from driving in the rain.
  15. Replies
    11
    Views
    3,352

    Re: Floor Pan Restoration

    I should point out that the floor pan on uni-body cars are a major part of the car's structure. Rivets, especially aluminum "pop" rivets, aren't going to provide the needed strength. If you don't...
  16. Replies
    12
    Views
    3,129

    Re: Exhaust bolt installation issue

    One thing I've found to make it easier is to lace a couple zip ties through the springs and compress them with a vice. Pull the zip ties tight and they'll hold the springs down and make it easier to...
  17. Replies
    11
    Views
    3,352

    Re: Floor Pan Restoration

    The current and previous issues of Car Craft have some pretty good articles on floor pan replacement. They're pretty generalized on the details, but it will point you in the right direction and give...
  18. Replies
    12
    Views
    7,983

    Re: Lizard Skin

    Can anyone speak to the durability as an undercoating?
  19. Replies
    10
    Views
    4,023

    Engine Re: Non-common block wanted

    Bummer, I just sent an '88 block and crank to the scrap yard.
  20. Replies
    41
    Views
    25,934

    Re: CSX VNT rear brakes

    Without having a Shelby Z rear caliper to directly compare, I'm wondering if other makes could be adapted. For instance, the Fiesta ST has rear discs with a caliper actuated parking brake, similar...
  21. Replies
    41
    Views
    25,934

    Re: CSX VNT rear brakes

    Perhaps we should start a thread with pics of each design, including casting numbers/part numbers and create a database that shows what parts came on what cars and see what interchanges with what. I...
  22. Replies
    41
    Views
    25,934

    Re: CSX VNT rear brakes

    I've not looked at the Neon stuff up close, but I believe the biggest difference between the CSX stuff and the '89-up production backing plates is going to be the guide pins for the calipers. ...
  23. Re: Omni GLHS alternator harness replacement

    Yes it should be.
  24. Replies
    1,308
    Views
    158,558

    Re: New LinOma-Bluffs Thread

    Yeah, that's becoming a dangerous road she was on, right in front of our kid's school. There was another similar accident less than a week later, and there's been three deaths on that road in the...
  25. Replies
    1,308
    Views
    158,558

    Re: New LinOma-Bluffs Thread

    As much as I'd like to, we simply can't budget it with me being in school and Amber having just bought a new car.
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4