Search:

How exactly will this save on wiring? Just run one fused (If you really want a fuse/safety before the relay) 30 amp relay and then after your feed wire splits add in two 10 amp fuses. I don't think...

already putting wheels on the car he can't drive.... hah.

Since the car is a money pit I would get the basics fixed before going too far with anything fun. Get the car driving to you can confirm...

TPS is also useful for interpreting datalogs.

Nice to have megasquirt when the TPS sensor changes. I know some people here say "it works" on stock electronics but they are not very close when you look at them on MS.

Yeah, the only purpose of the weld was to create and interference fit on my steel runners to the cut off upper aluminum flange. I would have had a steel flange made but when I was getting materials...

The Junkyard has 6L right now but I would probably go slightly smaller (4.5-5L?) if I had to save space. I think calculation wise the runner ID is only 1.38" in the slight velocity stacks and this is...

OP Joe sure dyno'd. Before and after :D Would have been awesome to see a dyno after cams with some fuel on the same boost as he ran on stock cams.

After getting a PM from someone on 3si who...

I would think the rippmod stuff is comparable, I would assume they used vortech blowers. So there are actually quite a few half built/failed projects out there and a few running ones. The only...

buy mo' P body

Not sure what parts I could use....since they are already junked.

I vote for dyno fund pool.
$10?

Think you had a cam seal fall out from poor installation? I have had the one in the distributor housing falling out before, my fault.

I want to run music with one but I don't know what I have to use to power the speakers etc while avoiding having an actual radio :P Like a race stereo :o

To get data from it you can just...

I guess the worst that could happen is you have to boot up the phone after turning the key on if you didn't drive for awhile. I have a spare T959 that gets to live in my Duster I guess :D
Is that...

The problem I see with a dash setup is powering on/off. Killing your battery or always waiting for shutdown/startup.

I think that MSdroid guy is from Utah too so I probably know someone who knows him :P I didn't ask around yet. I guess I can go buy all those bluetooth goodies now. My laptop battery is complete...

Well the cams probably ruined his VE table near idle rpms so AFR would have been off by 10-30%. Thats not saying its perfect now :P

Clearances are one thing but I do agree it is hard to go too far with cams performance wise.

My big cams with a 1.5 ratio rocker got maybe .5 to 1 mpg less driving to work, if that. Stock ecu,...

You are just talking about the contact patch of the roller moving from one side of the lobe to the other and thus touching a different part of the roller. I think that is taken into account in the...

Rocker ratio is definitely at least 1.6. Sorry for those who disagree.

How about a 6g72SKB
Some of those screw blowers are pretty tempting if you had a motor that could handle the torque (not something I want to try on stock rods if you want to push 600-1000ft/lb).

Well 6g72tt is not a real engine designation, just something we all made up. I run a 6g72TH on my daily :P
In JDM speak, it means fast. SR20de vs sr20det (except those are real engine designations...

Conquest is ....already out of parts so I don't get that one. Obviously they still keep moving along. Subaru front end (will probably go this route on at least one car) and then something else later....

I would just keep walbro in tank and 044 inline, stock tank etc. Thats good for everything you need and more. I don't think I like the fuel pump chart above because it seems more like a guess. By...

A lot weaker IMO. I went a little crazy. i took them out near to my planned bore size for the +.096 overbore I had in the forged shorblock. I still have the tracing template in a folder in the...

Was happy to see it on facebook. I would be happy with the results based on what went in. Probably healthier then my Holset Spirit. Side note about headgaskets. I also tried copper wire on an old...