Search:

Type: Posts; User: The Pope; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Re: Gauging interest in a new high capacity LM/SMEC/SBEC/SBEC2 flash module

    considering there is no support for a flashable factory computer and Ostrich is really the only option most of the time. I don't see how this not working with one would be useable other than the few...
  2. Re: Gauging interest in a new high capacity LM/SMEC/SBEC/SBEC2 flash module

    considering there is no support for a flashable factory computer and Ostrich is really the only option most of the time. I don't see how this not working with one would be useable other than the few...
  3. Thread: Head Porting

    by The Pope
    Replies
    157
    Views
    103,424

    Re: Head Porting

    My calipers I use to measure with are pretty sharp. I do a 1/4" curve and lay back the chamber that way
  4. Replies
    85
    Views
    124,771

    Re: Do you own a BMF? Status update please!

    You have to Rev to get more work done ultimately. So you need some top end for HP. Next is flow. So if the system is working, lowe pressure differential to zero. Then you look at a realistic psi per...
  5. General Re: T2 rad, 3 smecs, 1 sbec, 2 engine harness, A413 trans

    Is this a 90 turbo L body harness or a TBI 90 harness?
  6. Thread: Beehives

    by The Pope
    Replies
    7
    Views
    4,342

    Re: Beehives

    getting machining and paint. Then I have to make the timing cover gasket. Then photos lol
  7. Replies
    36
    Views
    14,346

    Re: Ported Stockers Revisited

    When I port a stocker I try to build a decompression area, like a plenum behind the #3 hole. Under pressure you aren't making 3 flow a ton better than 1. What you are doing is the same thing as...
  8. Thread: Beehives

    by The Pope
    Replies
    7
    Views
    4,342

    Re: Beehives

    my 354 is a Dodge D500 dump truck engine. The 354 stopped in 56 as a Chrysler engine. No 392 came in a truck. Then later trucks the 361 and 413 is industrial where as the hemi truck engines are not...
  9. Replies
    14
    Views
    5,601

    Re: PT lifter shimming question

    The first couple years were grade 5 and softer. I have old grade 8 gold washers that haven't crushed. Grade 8 hardened washers can't maul flat like that in an aluminum bore. The force it takes to...
  10. Thread: Beehives

    by The Pope
    Replies
    7
    Views
    4,342

    Beehives

    It is amusing that after using Magnum V8 beehives in the 2.2 that I have now found a 3 rd Mopar in need of the beehives. The low installed height causes lift issues with bind. The early first gen...
  11. Replies
    14
    Views
    5,601

    Re: PT lifter shimming question

    The washer I always used from Fasteners is grade 8 and doesn't deform to the aluminum bore. They are smaller than the bore for OD and press the bottom washer into the lifter bore and sit flat. The...
  12. Thread: BoostButton

    by The Pope
    Replies
    40
    Views
    33,132

    Re: BoostButton

    Any news on these?
  13. Thread: BoostButton

    by The Pope
    Replies
    40
    Views
    33,132

    Re: BoostButton

    Hope someone is able to carry on, I am sure I am not the only one that was in need soon.
  14. Replies
    26
    Views
    14,377

    Re: Is OMNI-Potent still around?

    Need to pay the domain bill
  15. For Sale Re: Fleet of Shelby Dodges For Sale / Seattle,Wa

    My dad bought the Rampage, it is actually getting new paint down the street already lol, I bought the 89 CSX 170. The 89 CSX 440 is a really nice car, just needs some wax I think. Some one into the...
  16. Re: How much hp is a slightly ported 1pc intake good for

    For clarity, as some may be confused by my first sentence after I read it. Lets look at some rough math based off of my flow numbers. Cams change things too but we'll leave that out for now.

    122...
  17. Re: How much hp is a slightly ported 1pc intake good for

    fact is air plus fuel is going to equal HP, higher RPM equals more HP with the same air flow. The 1 piece restricts RPM and air flow. Slamming 30+ PSI to one you are going to get some air through it....
  18. Replies
    14
    Views
    4,187

    For Sale Re: 1991 daytona race car $64,000.00

    last time it was for sale it was about 20K. real nice car though
  19. Engine Re: WTB- 44mm intake valves for G head and oversize seats

    seats are pretty easy to get, who sells a new 44mm G head valve? Manufacture.
  20. Re: A true S60 roller cam-now available-regrind or new billet!

    didn't see the R4 on the web site, how much are stock base circle cams?
  21. Re: Ported stock mani good for 550hp+, so whats the point of headers?

    Glycol doesn't transfer heat well and it freezes at 10 degrees. So normally not many want to run it straight. However with a turbo and exhaust temps way up there your boiling point being way higher...
  22. Re: Ported stock mani good for 550hp+, so whats the point of headers?

    Well pure isn't really 100% with most. But yeah I run pure the I have to top off a couple times as the water burns out. Then all bubbles and burping leaves. Not a popular plan but with boiling issues...
  23. Re: Ported stock mani good for 550hp+, so whats the point of headers?

    When you look at guys building $5,000 headers for expensive V8 builds the people selling those headers tell you the same thing, how much you spend = how long they last. Tube headers just don't last...
  24. Re: Gauging Interest- Chrysler .63 A/R turbine housing Group Buy

    they look good, should be fun
  25. Replies
    31
    Views
    11,420

    Re: tranny giving it up, no mechanic understands

    fun times.
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4