Search:

Type: Posts; User: tryingbe; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.72 seconds.

  1. Replies
    9
    Views
    2,569

    Re: Whose running a standalone?

    Microsquirt.

    Don't need HEP and my friends use MS.

    ...
  2. Replies
    2
    Views
    2,685

    Re: L body rear wheel alignment

    Loosen the 4 bolts for the spindle is all you have to do, no need to remove any of the drum brake parts.


    http://www.thelostartof.net/tryingbe/forsale/shims.jpg
  3. Replies
    912
    Views
    201,380

    Re: Turbonator LM codebase

    Run both and see which one you like better.
  4. Thread: Microsquirt

    by tryingbe
    Replies
    90
    Views
    16,621

    Re: Microsquirt

    I used 420A coil wires.

    https://thelostartof.net/tryingbe/dodge/omniproject/2017/microsquirt/coil.jpg

    https://thelostartof.net/tryingbe/dodge/omniproject/2020/underhood/engine1.jpg
  5. Re: Microsquirt (less expensive/super compact/less feature version of megasquirt)

    I just followed the diagram. http://www.minimopar.net/ecu/lm-1987-t2.html

    Blue connector pin #3 for a/c cut out relay. This means ECU can disengage A/C like it WOT condition or if engine coolant...
  6. Replies
    7
    Views
    1,725

    Re: What is the signal for the tachometer?

    It's just an on/off 0-12v digital signal, my Microsquirt output to the Daytona Digital dash with no issue.
  7. Replies
    5
    Views
    1,482

    Re: knock sensor dead ?

    Super 60 ECU doesn't use knock sensor nor o2 sensor.
  8. Replies
    11
    Views
    1,875

    Re: Fan relay max amperage

    Nothing stood out from the picture other than you don't have working a/c.

    I'm using a Volvo 850 fan in my GLH with custom shroud made from computer case panel. All gap is seal so air has only one...
  9. Replies
    11
    Views
    1,875

    Re: Fan relay max amperage

    Do you have working a/c?
    What your coolant capacity?
    Picture of the engine bay?
  10. Replies
    11
    Views
    1,875

    Re: Fan relay max amperage

    220F on street or freeway? What are you using to determine the coolant temperature?

    Factory calibration won't even turn fan on above 45mph until the temp is above 218F....
  11. Re: Drive shaft rebuild parts list (bearings, boots, cages, etc.)

    Boot is easy to get.

    https://www.rockauto.com/en/catalog/dodge,1988,omni,2.2l+135cid+l4,1094644,drivetrain,cv+joint+boot,2284
  12. Thread: Microsquirt

    by tryingbe
    Replies
    90
    Views
    16,621

    Re: Microsquirt

    Took me a couple of nights to fine tune the little knock meter's configuration on a 2.2L and I used a BOSCH wideband knock sensor.

    Is the Mitsubishi knock sensor a wideband sensor? Turbo Dodge...
  13. Replies
    418
    Views
    71,014

    Re: So what are you Guys reving your 2.5L's to?

    What fuel did you use?
  14. Thread: Microsquirt

    by tryingbe
    Replies
    90
    Views
    16,621

    Re: Microsquirt

    I used a Volvo resistor. I'm sure you can find it much cheaper used at http://forums.turbobricks.com/

    One wire in from 12v source, four wires out connected to the four injectors, then the other...
  15. Replies
    1
    Views
    1,207

    Re: Digi Dash Troubleshooting

    Picture of what you have will help.
  16. Thread: Microsquirt

    by tryingbe
    Replies
    90
    Views
    16,621

    Re: Microsquirt

    Add more fuel to Priming Pulse, Cranking Pulse, AfterStart Enrichment, Warmup Enrichment.

    https://www.msextra.com/forums/viewtopic.php?t=46234
  17. Replies
    9
    Views
    2,220

    Re: Tune adjustment?

    As you know, no factory car ever come with 2.5L and G head. But all the other engine setup use 12 degree as baseline.

    As general, G Head require more timing than 782 head but 2.5L needs less...
  18. Replies
    9
    Views
    2,220

    Re: Tune adjustment?

    12 degree spark timing with engine coolant temperature sensor unplugged.
    Make sure the cam shaft is timed correctly. http://www.thedodgegarage.com/timing_belt.html

    Contact FWD performance and see...
  19. Thread: Microsquirt

    by tryingbe
    Replies
    90
    Views
    16,621

    Re: Microsquirt

    This is my cost from 2017. You'll need to update it and see if you can do it cheaper.

    MicroSqurit Total Cost -$1,470

    36-1 wheel welded to crank -$100
    Balanced crank pulley -$74.31
    Microsquirt...
  20. Replies
    98
    Views
    108,096

    Sticky: Re: RockAuto discount code!

    I think all human left RA. RA sent someone else's rotors/pads/calipers but there is no one to call at RA and only line direction to follow. If I was going to return the item, "I" would have to pay...
  21. Replies
    31
    Views
    5,518

    Re: High amp alternator wiring

    Alternator gets ground from the block. My ground cables goes from the block to the negative side of the battery.
  22. Replies
    31
    Views
    5,518

    Re: High amp alternator wiring

    I used 1/0 welding cable to make my alternator to battery, battery to starter, and battery to ground cables.

    Yes, it's overkilled, but I'll never have issue again.
    ...
  23. Replies
    3
    Views
    1,504

    Re: How hot does a turbo get ?

    https://www.researchgate.net/figure/Maximum-gas-temperature-at-different-positions-in-the-exhaust-gas-train-of-an-automotive_fig2_215904692
  24. Replies
    3
    Views
    1,504

    Re: How hot does a turbo get ?

    It can get even hotter.

    Just make sure your ignition timing is right and send it.
  25. Replies
    6
    Views
    4,561

    Re: Exhaust noise hi RPMs

    Got any other muffler laying around to test?
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4