1 Attachment(s)
FS/FT 1987 Dodge Daytona Shelby Z project
Date: 19th January 2015
Username: moparman76_69
Full Name: George Manning
City, State, Zip: Indianapolis, IN
Contact: PM, will supply phone and email
Selling or Wanted Price: 800 OBO with the parts I have included, I'll continue working on it as I still have it and the price will reflect that
Description: 1987 Dodge Daytona Shelby Z
I've got the previous issues resolved in a way, the AIS is for now disabled and the car idles at 900-1000 rpm. I've decided to pass this on as a good start for a project so I can put the money back into finishing the van finally.
2.2/A555 Has a TII one piece and Garrett turbo
Entire brake system was replaced recently including new hardlines
Large FMIC
Accufab rail mount AFPR
Innovate LC-1 with Red DB-2 gauge
Has the TII radiator but not the factory intercooler.
2.5" downpipe with 3" exhaust and magnaflow muffler
The headlight motors still work
I put the set of Monroe struts with 1 coil cut off springs I had on the van on the front
What it needs ASAP
The power steering pump has been removed and the lines looped at the rack
The front end needs bushings and an alignment
It still has the 87 style rear discs and the e brake was never reconnnected
The battery currently in the car goes to my truck, I'll be pulling it out before the car is sold.
Again 800 and I'll include the following
6 bolt AL flywheel
A520 3.5 final with a moly plate installed
A different one piece gasket valve cover since the one on it appears to need the baffle resealed
A poly front motor mount
Ebay BOV with adapter pipe to replace the Talon valve that is crushed too far to work properly.
Spirit R/T rack that has been in my attic for two years, I can probably dig up a P/S pump and bracket so the power steering can be hooked back up
I have a set of 6.5 crabs that can go with the car, the tires on them are bald. I'd need to keep the wheels on the car now if you wanted them so I can keep that car a roller.
The car will run and drive but I wouldn't want to take it on a long road trip home, I'd say you'd need to tow it home. The car that has the crabs on it is an 89 sundance with no title. I could work a hell of a deal for you if you wanted both cars and a load of parts to take home.
http://i634.photobucket.com/albums/u...psf07d63db.jpg
http://i634.photobucket.com/albums/u...ps19112f38.jpg
http://i634.photobucket.com/albums/u...ps02uq3nu7.jpg
http://i634.photobucket.com/albums/u...psucbf98pf.jpg
http://i634.photobucket.com/albums/u...pslvepzkyk.jpg
http://i634.photobucket.com/albums/u...psswsd7uwc.jpg
Re: FS/FT 1987 Dodge Daytona Shelby Z project
Bump, I updated the first post to reflect the current condition.
Re: FS/FT 1987 Dodge Daytona Shelby Z project
Bump again, I need this thing gone.
Re: FS/FT 1987 Dodge Daytona Shelby Z project
Is all the interior present and matching? In the picture it looks like the passenger seat is missing and the dash is a different color...
Re: FS/FT 1987 Dodge Daytona Shelby Z project
It went missing at some point. I installed a XSpower intercooler with the same side inlet/outlet to replace the ebay one with the miles of piping, I also replace the non-functioning BOV with a ebay type RS knockoff. I have to set the boost controller so it won't hit cutoff and most all of the bugs with the running part have been worked out. If it doesn't sell in the next week, I'll end up keeping it at least through the summer and putting a set of tires on it.
Re: FS/FT 1987 Dodge Daytona Shelby Z project
One good wheelhopping session or a 1-2-1 misshift will finish off that trans case.
Or a protruding manhole cover for that matter. :(
Don't ask how i know.