Alternate parts thread-OEM to aftermarket-post findings!

Thanks to Simon and others who contributed to the original thread...:D

Post parts you have found that fit TIII's that are from other cars, and aftermarket suppliers.

1.) The front crank seal is CR part #11111,

2.) The cam seals are #14707-CR stands for Chicago Rawhide. You can use these numbers to cross over to any other brand, IE National etc.

3.) Dodge Viper oil cap, I took the gasket off the Viper oil cap and put it on my stocker.

4.) TI/TII/TBI commonblock can be substituted for a trashed TIII block. Grind in the water pump passage area for clearance for the water deflector. Place a core plug in the distributor hole. Crankcase breather can be added by drilling a hole in the distributor core plug and installing breather there (before installing plug!). TBI block will also need to be drilled for turbo oil return on the rear of block.

5.) Substitute thermostat gasket: Use a thermostat gasket from a '94 Dodge 5.2 V8.

6.) Head studs... Acura VTEC B18C1, 11mm. arp part number 208-4303 they are the 11mm ones for the 1.8 vtec. I had to go this route when building my engine because our vendors were out of stock, but everyone and their mothers sell honda parts.

7.) Part numbers through Goodyear for:
Radiator hose, upper 61782
Idler pulley/Serp tensioner pulley's- 49038
Radiator hose, lower 61341
Timing belt 40206
Heater hose, heater to waterpump 63073
Serpentine belt 4060785
Heater hose, heater to engine 63275

Belt numbers for no a/c or UDP.

Stock belt: 060790
Non A/C: 060660
Non A/C & UDP: 060637

I found Dayco belt # 5060670 fit with no a/c, the 60 was too short.

You insert vendors choice for the first number, IE Dayco would be a 5060790, Goodyear a 4060970 etc.

Category/ Part/ Brand/ Aftermarket Part # / OEM Equivalent
Sensors
Crankshaft Position Sensor:
Borg Warner CSS72
Niehoff AL2024

Camshaft Position Sensor:
Borg Warner CSS74

Oxygen Sensor (4 wire):
Bosch 13275

Fuel Injector (4 total):
GP Sorenson 800-1047N 5277895

Washer Fluid Level Sensor - Front:
Niehoff AL1005

Washer Fluid Level Sensor - Rear:
Niehoff AL1006

Coolant Level Sensor:
Niehoff AL1010

Water Temp. Switch (Gauge):
GP Sorenson TSU113

Ambient Air Temp Sensor (For Overhead Console Cars):
GP Sorenson TSU180

Air Charge Temp Sensor:
Niehoff TS81261

Throttle Position Sensor:
Niehoff FE1088 5234901
Standard TH136 5234901

Knock (Detonation) Sensor:
GP Sorenson KS1 5213629
Borg Warner S799 5213629
Standard KS1 5213629

M.A.P. Sensor:
Niehoff FE-1627 5234327
Standard AS25 5234327

Idle Air Control Valve:
Niehoff 21811 4612159; 4612673; 5277839
Borg Warner 21811 4612159; 4612673; 5277839

Coolant Temperature sensor (2 Pin):
Niehoff TS82231
GP Sorenson TSU110

Coolant Temperature sensor (3 Pin):
GP Sorenson TSU89 4267281

Oil Pressure Switch (Gauge):
GP Sorenson OPS121

Fuel Pressure Regulator:
Niehoff 22823 4306015

Fuel Pump (Assembly Including Pump and Strainer):
Carter P74631H

Fuel Tank Sending Unit (Float Gauge Assembly):
Spectra Premium FG64B

Fuel Tank (Daytona):
Spectra Premium CR2G

Fuel Tank Straps (Daytona):
Spectra Premium ST17

Engine Mounts:
Right Side Motor Mount (Upper Passenger Side) Anchor 2616
Poly Bushings #1000 Note: this mount is polyurethane

Front Motor Mount (Below Radiator on Core Support):
Anchor 2615
Poly Bushings #3419 Note: this mount is polyurethane

Engine Gaskets and Seals
Rear Main Seal :
National 710056 4621939AB, 4667904, MD101915, 4621939, 4667322, 5203590, MD120699
Fel-Pro BS40168-1 Made From Rubber, One Piece
Fel-Pro BS40627 Made From Teflon, One Piece
Timken 710056 Made From Viton, One Piece
Timken 5279 Made From Teflon, One Piece

Intake Manifold Gasket (Plenum Gasket set):
Standard PG34 4343703

Intake Manifold Gasket and Exhaust Manifold Gasket Set:
Mopar 4728214AB

Front Crank Seal:
Chicago Rawhide 11111 4273275
National 3638 4273275
Gates KS11122
Timken 3638

Front Crank Seal Repair Sleeve:
National 99112
Timken KWK99112

Camshaft Seal (2 Required):
Chicago Rawhide 14707 4424059
National 223801 4424059
Gates KS13948
Timken 223801

Camshaft Seal Repair Sleeve (2 Required):
National 99147
Timken KWK99147

Auxiliary Shaft Seal :
National 3655 4105388, 4105389, 4105395, 5203465

Auxiliary Shaft Seal Repair Sleeve:
National 99139

Water Outlet Gasket:
Fel-Pro 35286

Head Gasket:
Mopar 5013602AA
Cometic C5733-65 This is a Multi - Layer Steel - Shim Gasket 0.065 Inches Thick

Valve Cover Gasket (Sold Individually):
Mopar 4484489

Valve Stem Seals (Sold in Set of 16):
Mopar 4424030

Engine Miscelianious
Timing Belt:
Mopar 4667530
Gates T206
Goodyear 40206
Dayco 95206

Head Bolts:
Mopar 6502219
ARP 241-3701 12-Point Head

Head Studs:
ARP 241-4501 Hex Nuts
ARP 241-4701 12-Point Nuts

Main Studs:
ARP 141-5401

Connecting Rod Bolts:
ARP 141-6001 High Performance Complete
ARP 141-6021 High Performance 2 piece
ARP 141-6401 High Performance Wave Complete

Camshaft Sprockets:
FWD Performance FWD 43-0802 Note: These Sprockets are Adjustable and Available in Multiple Colors

Lifters (Set of 16):
FWD Performance fwd 43-0199

Oil Fill Cap:
Stant 10066
Gates 31066

Electrical
Horn - Low Note:
Niehoff UN451

Horn - Low Note (High Out Put):
Niehoff UN458

Horn - High Note:
Niehoff UN450

Horn - High Note (High Out Put):
Niehoff UN457

Power Window Switch (Driver's Side; 2 Button):
Mopar 4688229
Niehoff MC56591
Dorman 49224

Rear Defogger Switch (Daytona):
Niehoff MC59101

Cruise Control Switch Assembly (Daytona):
Niehoff CC21211

Back-up light Switch:
Niehoff NS37011

Door Jam Switch (Courtesy Lamp Located on A - Pillar):
Niehoff DJ40201

Door Jam Switch (Door Ajar Located on B - Pillar):
Niehoff DJ40211

Head Lamp Switch Assembly (Daytona W/ Fog Lamps):
Niehoff HL20201

Turn Signal Switch:
Niehoff DS50111

Ignition Switch (Daytona):
Niehoff IG69301

Front Windshield Washer Pump:
Niehoff WP7966
Trico 11-514
Dorman 88113

Rear Tailgate Washer Pump:
Trico 11-507
Dorman 88114

Front Windshield Wiper Motor:
Dorman 601-300 Note: This Part is New
Cardone 85-388 Note: This Part is New
Cardone 40-388 Note: This Part is Remanufactured

Rear Windshield Wiper Motor:
Cardone 40-397 Note: This Part is Remanufactured

Turbo
Blow Off Valve:
Mopar 4504564


Heating and Cooling
Water Pump (New):
GMB/ Prestone 120-3060 4626682/ O.E. Casting #4483455

Thermostat:
Prestone 338-192

Bypass Hose (Heater to Engine):
Goodyear L-63275
Gates 18948

Bypass Hose (Heater to Water Pump):
Goodyear 63073
Gates 18075

Bypass Hose (Heater to Oil Cooler):
Gates 18987

Upper Radiator Hose:
Goodyear 61782
Gates 21639
Dayco 71279

Lower Radiator Hose:
Goodyear 61341
Gates 21674

Idler Pulley:
Goodyear 49013

Tensioner Pulley:
Goodyear 49038

Serpentine Belt:
Goodyear 4060785 or 785K6
Gates K060785
Dayco 5060785

Radiator Fan Assembly (Motor Included):
Dorman 620-008

Radiator Fan Motor :
Seimens PM3310

Radiator Cap:
Stant 10231 or 10331 Note: Cap is Rated at 16 PSI
Gates 31516 or 31523 Note: Cap is Rated at 16 PSI

Air Conditioning
A/C Low Pressure Cut-out Switch:
Niehoff HS-30271

A/C Condenser:
Factory Air 54329

A/C Receiver Drier/ Accumulator:
Four Seasons 33550

A/C Evaporator Core:
Four Seasons 54109

A/C Expansion Valve (Block Type Flange):
Four Seasons 38849

A/C Compressor (Remanufactured LTR4, With Clutch):
Four Seasons 57235

Selector Vacuum Switch:
Niehoff HS-30341

Blower Control Switch:
Niehoff HS-80511

Blower Motor:
Siemens PM299

Engine Filters and Tune-Up

Air Filter:
Fram CA3660

P.C.V. Valve:
Fram FV163

Crankcase Breather Filter:
Fram BA6662

Carbon Canister Filter (4.5in Dia.):
GP Sorenson 779-1000

Ignition Coil:
Wells C939

Spark Plug:
Champion RN12YC Copper
Champion 3405 Platinum
NGK GR4IX Iridium
NGK GR4GP Platinum
NGK GR4 V-Power
Bosch WR8DP Platinum
Splitfire SF6C Copper
Splitfire TP6C Platinum

Spark Plug Wire Set:
Accel 5109R Note: wires set is red

Chassis and Suspension
Power Steering Pressure Hose:
Edelmann 71918

Power Steering Return Hose:
Edelmann 71899

Power Steering Pump:
Cardone 20-863 frim feel stearing code SBA; Note: this part is remanufactured

Power Steering Pump Cap:
Dorman 82577

Power Steering Pressure Sensor:
Niehoff AL9000

Complete Power Steering Pump Rebuild Kit:
Gates 350390

Rear Track Bar Replacement Bushings:
Poly Bushings #1025 Note: this part is polyurethane

Rear shock:
KYB 343164

Rear Axle to Frame Bushings:
Poly Bushings #1036

Front Strut:
KYB 235045

Front Strut Upper Mount with bearing:
Monroe 901908

Front Strut Upper Spring Seat:
Monroe 902993

Front Strut Lower Spring Seat:
Monroe 903980

Front Lower Ball Joint:
TRW 104178

Inner Tie Rod:
TRW ES3061R

Outer Tie Rod End:
TRW ES3008R

Rack and Pinion Assembly:
Cardone 22-336 frim feel stearing code SBA, manual trans, 16inch wheels; Note: this part is remanufacuted

Rack and Pinion Assembly Mounting Bushing:
TRW HB1212

Lower Control Arm Bushings:
TRW HB1750K

Sway Bar Bushing to Control Arm 1" Bar:
TRW HB1806

Sway Bar Bushing to Frame 1" Bar:
TRW HB1620

Sway Bar Bushing to Control Arm 1 1/16" Bar:
TRW HB1807

Sway Bar Bushing to Frame 1 1/16" Bar:
TRW HB1621

Sway Bar Bushing to Control Arm 1 1/8" Bar:
TRW HB1616

Sway Bar Bushing to Frame 1 1/8" Bar:
TRW HB1622

Brakes
Front Brake Pads; Semi - Metallic:
Raybestos PGD522M

Front Brake Rotor:
Raybestos 7992

Front Brake Caliper - Right:
Reman Parts Inc. 4315 OEM Casting #12391901 ; Note This Part is Remanufactured
Dorman CA10904R O.E.M. #4423716 ; Note: This Part is New
Cardone 18-4362 Supplied With Hardware, Phenolic Piston Supplied Without Mounting Bracket
Cardone 18-B4362 Supplied With Hardware, Phenolic Piston Supplied With Mounting Bracket
Cardone 18-4362S Supplied With Hardware, Metal Piston Supplied Without Mounting Bracket
Cardone 18-B4362S Supplied With Hardware, Metal Piston Supplied With Mounting Bracket
Cardone 16-4362 Supplied With Pads and Hardware Phenolic Piston
Cardone 16-B4362 Supplied With Pads and Hardware Metal Piston
Cardone 15-4362S Supplied With Servre Duty Pads And Hardware Phenolic Piston
Cardone 15-B4362S Supplied With Servre Duty Pads And Hardware Metal Piston

Front Brake Hose With ABS - Right:
Coni - Seal BH177917

Front Brake Caliper - Left:
Reman Parts Inc. 4316 OEM Casting #12391901 ; Note: This Part is Remanufactured
Dorman CA10903L O.E.M. #4423717 ; Note: This Part is New
Cardone 18-4363 Supplied With Hardware, Phenolic Piston Supplied Without Mounting Bracket
Cardone 18-B4363 Supplied With Hardware, Phenolic Piston Supplied With Mounting Bracket
Cardone 18-4363S Supplied With Hardware, Metal Piston Supplied Without Mounting Bracket
Cardone 18-B4363S Supplied With Hardware, Metal Piston Supplied With Mounting Bracket
Cardone 16-4363 Supplied With Pads and Hardware Phenolic Piston
Cardone 16-B4363 Supplied With Pads and Hardware Metal Piston
Cardone 15-4363S Supplied With Severe Duty Pads and Hardware Phenolic Piston
Cardone 15-B4363S Supplied With Severe Duty Pads and Hardware Metal Piston

Front Brake Hose With ABS - Left
Coni - Seal BH177916

Front Brake Caliper Seal Kit - 60mm Piston:
Coni - Seal 66517

Front Brake Caliper Banjo Bolt:
Dorman 13939 Thread: 7/16 x 20; Length: 7/8 inch; Hex Size: 5/8 inch

Front Brake Caliper Slide Bolts:
Carlson H5066 comes in a set of 2 bolts and 2 sleeves

Front Wheel Stud:
Dorman 98480 M12 x 1.5

Rear Brake Pads; Semi - Metallic:
Raybestos PGD415M

Rear Brake Rotor (Vented):
Raybestos 7993

Rear Brake Rotor (Non - Vented):
Raybestos 76002

Rear Brake Caliper - Right (Vented Rotors):
Reman Parts Inc. 4303 OEM Casting #120753

Rear Brake Caliper - Right (Non - Vented Rotors):
Reman Parts Inc. 4301 OEM Casting #120492

Rear Brake Caliper - Left (Vented Rotors):
Reman Parts Inc. 4304 OEM Casting #120753

Rear Brake Caliper - Left (Non - Vented Rotors):
Reman Parts Inc. 4302 OEM Casting #120492


Rear Brake Hose:
Coni - Seal BH177809

Rear Brake Cable - Right:
Raybestos BC93944

Rear Brake Cable - Left:
Raybestos BC93944

Rear Parking Brake Hardware Raybestos:
F138098S

Rear Wheel Stud (Rear Disc Brake Equipped):
Dorman 97045 M12 x 1.5

Wheel Lug Nuts (Chrome Capped) Dorman 98976 M12 x 1.5

Brake Master Cylinder:
Cardone 13-1983 Note: New; Reservoir Included
Cardone 10-1983 Note: this part is remanufactured, no reservior

Power Brake Booster (Remanufactured):
Cardone 54-73172

Stop Light Switch (Daytona):
Niehoff SL-78211

ABS Hydraulic Unit (Remanufactured):
Cardone 12-2107

ABS Control Module:
Cardone 12-1103 5234235

ABS Sensor - Front Right:
Raybestos ABS530348

ABS Sensor - Front Left:
Raybestos ABS530349

ABS Sensor - Rear Right:
Raybestos ABS530080

ABS Sensor - Rear Left:
Raybestos ABS430351

ABS Relay:
Niehoff RL-35491 O.E.M. #4687246

Master Cylinder Cap:
Dorman 42044

Master Cylinder Cap Gasket:
Dorman 42081

Brake Pedal Pad:
Dorman 20727

Spindle Nut - Front :
Dorman *05183

Spindle Nut - Rear
Dorman *05190

Front Hub Assembly:
SKF CBR930013
SKF BR930013
BCA/ National 513075
Timken 513075

Rear Inner Bearing:
BCA/ National A-39
Timken Set46

Rear Outer Bearing:
BCA/ National A-16
Timken Set16 Note: Bearing has Stamping LM12749F, and Race has Stamping LM12711

Rear Inner Seal:
BCA/ National 4099
Timken 4099

Rear Wheel Dust cap:
Dorman 13975

Transmission/ Clutch/ Axle
Manual Transmission Mount (Mid shock tower, driver's side):
Anchor 2618
Poly Bushings #PB2618 Note: this mount is polyurethane

Manual Transmission Bobble Strut:
Poly Bushings #3297 Note: this part is adjustable

Clutch Pedal Pad:
Dorman 20727

Shifter Cable :
Dorman 16653

Clutch Cable:
Raybestos BC94374
Autospecialty CA-83007

Clutch Release Bearing:
Timken 614092
BCA/ National 614092

New Clutch Set:
Fenco NU0066SC

Clutch Fork:
Dorman 14565

Inner Clutch Fork Bearing:
Dorman 14337

Outer Clutch Fork Bearing:
Dorman 14345

Clutch Switch:
Niehoff AL-2500

Differential Bearing (2 Required)
Timken Set11

Differential Bearing Repair Sleeve (2 Required):
Timken KWK99157

Differential Housing Seal:
Timken 3459S
National 3459S

Input Shaft Bearing:
Timken Set4

Input Shaft Seal - Front:
Timken 3732S

Input shaft Seal Repair Sleeve - Front:
Timken KWK99106

Input Shaft Bearing - Rear:
Timken Set5

Axle Shaft - Left Side:
USA Industries AX-65299 Note: This Part is Remanufactured
Cardone 60-3025 Note: This Part is Remanufactured
Cardone 66-3025 Note: this Part is New

Axle Shaft - Right Side
USA Industries AX-65299 Note: This Part is Remanufactured; Equal Length Driveshafts
Cardone 60-3025 Note: This Part is Remanufactured; Equal Length Driveshafts
Cardone 66-3025 Note: This Part is New; Equal Length Driveshafts
USA Industries AX-65309 Note: This Part is Remanufactured; Un-Equal Length Driveshafts
Cardone 60-3034 Note: This Part is Remanufactured; Un-Equal Length Driveshafts
Cardone 66-3034 Note: This Part is New; Un-Equal Length Driveshafts

Inner CV Boot:
Dorman 614-002

Outer CV Boot:
Dorman 614-003

Nice job Rich! :thumb:

GP Sorensen part # CSS40 $38.88 normally stocked (Advance Auto Parts)

It requires cutting the plastic back around the plug, and soldering the pigtail from your old sensor (or a spare HEP... same connector:) ) to the terminals. It also requires filing a flat into the plastic body of the new sensor in the same location as the flat on the stock sensor. Other than that, it's a drop-in replacement. The body is the same length, and the bolt hole is in the right spot.
I just got my Spirit running off of one today, so no long term results yet, but it's working great so far.:thumb:
Maybe someone else can benefit from my experimenting. Sure beats paying $150-$200 for one.:)

Paint:
Code PRB Radiant Fire
Duplicolor
1/2 oz bottle/brush (scratch fix) part# NGCC382
5 oz spray can part # DSCC382

ARP-200-8530 7/16ID 13/16OD BLK WASHER

Is the washer that is used with the ARP Studs

4 into 1 vacuum connector on front of block from Dodge. (part# 04504024)

How is this not in the KC?

thank you for this post! Great resource wish I had found this years ago!

Quote:

---

Originally Posted by 4cefedomni

How is this not in the KC?

---

i second that.

Because its right here in the TIII section, lol. No one checks the KC, but if your here in the TIII section, then you see it, :p

At least on my car (1992 Spirit R/T), the power steering pump is NOT Cardone 20-863 firm feel steering - that unit is a Saginaw rebuild, not a ZF. It is Cardone 2040887 (or any of the other part numbers listed on RockAuto), which is unfortunately quite a lot more expensive and also requires sending in the original pump to be rebuilt. I don't know whether Gates 350390 is the correct power steering pump rebuild kit, but I suspect it is, since it's listed on RockAuto as well - so far, for me, RockAuto's been pretty good about getting TIII parts correct (unlike some other suppliers).

EDIT: Well, turns out that Gates 350390 is for the Saginaw, not the ZF. I'll post up the right P/N when I find it.