-
Older Activity
-
09-27-2023, 09:27 AM
+1 great seller and very knowledgeable about our cars. Awesome guy!
Sent from my SM-S916U using Tapatalk
5 replies | 125 view(s)
-
09-26-2023, 01:25 PM
I got it, it was just really stubborn. I tried to delete post so here is an explanation I couldnt get the red pin lock out of the 60 pin. I tried a...
0 replies | 81 view(s)
-
09-23-2023, 05:56 PM
Get a lil heat into it with like a map gas torch, then use an ease out on it.
Sent from my SM-S916U using Tapatalk
11 replies | 267 view(s)
-
09-19-2023, 09:28 AM
I sent an email to OTC to find out if the 4000E modifies it's display of information coming from the ecm. The following is a copy of the body of that...
16 replies | 1309 view(s)
-
09-15-2023, 05:23 PM
I also plan on running it in a g-head, so hopefully it'll work out for me too.🤞
Wheel bearing grease 🤔, might give that a try as well.
Sent from...
4 replies | 224 view(s)
-
09-15-2023, 08:54 AM
Brian, I recently tried a different tuning strategy, that is, I downloaded from TM the file T-SMEC_25_MTX_A131_MP.TPL. I loaded my tune and that one...
16 replies | 1309 view(s)
-
09-14-2023, 05:50 PM
I disagree, not trying to be antagonistic but arbitrary is not the correct word because the definition is the opposite of the inferred meaning....
16 replies | 1309 view(s)
-
09-13-2023, 05:38 PM
Pm sent
Sent from my SM-S916U using Tapatalk
4 replies | 224 view(s)
-
09-13-2023, 05:36 PM
Pm sent
Sent from my SM-S916U using Tapatalk
2 replies | 176 view(s)
-
09-13-2023, 10:06 AM
I just had an idea for consideration. Is it possible that when the OTC 4000 reports zero degrees timing at WOT that it is actually saying that...
16 replies | 1309 view(s)
-
09-12-2023, 10:25 PM
Jeff, my Charger has a SMEC ecm. Does your memory hold true for that type of control as well. Is it possible that you might have even better info for...
16 replies | 1309 view(s)
-
09-03-2023, 10:31 PM
Actually, my friend Lohnnie has a lift, that's a better idea. Thanks for the caution.
16 replies | 1309 view(s)
-
09-02-2023, 08:13 AM
My thinking was that with the car up on Jack stands, third or fourth gear and lots of brake input at full advance timing should be in the 0-12...
16 replies | 1309 view(s)
-
09-01-2023, 11:29 PM
Thanks Warren. Wow. That piece is impressive but obviously a machine shop is needed to create it. Beyond my means but thank you for digging up the...
41 replies | 4447 view(s)
-
09-01-2023, 12:57 PM
Yupp, that's the one I bought. Thanks Miles.
41 replies | 4447 view(s)
-
09-01-2023, 08:43 AM
Todd, I noticed the difference right away. I borrowed one from Jackson when I tried to do the change recently, but the length seemed to make it...
41 replies | 4447 view(s)
-
replies | 144 view(s)
-
08-31-2023, 09:11 PM
So, you put the hooks over the shaft on the fuel rail? Your KD tool must have been un modified.
41 replies | 4447 view(s)
-
08-31-2023, 09:04 PM
Doesn't that have to use the cam a a pivot point? I was going to take the cam off the head. As a side note I have the two piece intake. Also, is that...
41 replies | 4447 view(s)
- Age
- 49
About minigts
- Biography:
- Born and raised in Memphis. Been working on my car since 1991 when I first purchased it. Originally the car had 65K miles and ran like a top. Over the years, it started running more like a top with arthritis. Eventually I installed a TII motor setup and now it runs like a top again on steroids.
Also purchased a 1992 IROC R/T with 65K miles on it and drove it from it's original home, Anchorage, AK. A total of 5,238 miles from start to finish and about 15 gallons of antifreeze along the way. With a blown headgasket (thankfully) and all season tread tires, my friend and I traversed the Alaskan highway through the Yukon and BC, Canada to Seattle, WA and then across the country to its new home Memphis, TN.
Future plans for each car are to continue to customize the Shelby and restore the Daytona. Both require money and time, neither of which I have a lot of at the moment.
- Location:
- Memphis, TN
- Interests:
- Cars, computers, family (wife only)
- Occupation:
- Software Trainer
- Myspace Profile:
- Myspace is retarded
- Facebook Profile:
- Facebook is also retarded
[SIGPIC][/SIGPIC]
[SIZE="3"]
[B]Jon Trotter[/B][/SIZE]
[B]1985[/B] Dodge Shelby Charger, Currently decommissioned
[B]1987[/B] Shelby GLHS, #937
[B]1987[/B] Shelby Lancer, #628
[QUOTE=Reeves;587010]I can be ready. Please send pics of wife.
_____DodgeZ add comments here______[/QUOTE]
Total Posts
- Total Posts
- 6,890
- Posts Per Day
- 1.06
- Last Post
- Connectors 08-20-2023 10:25 PM
Visitor Messages
- Total Messages
- 1
- Most Recent Message
- 10-30-2014 11:40 PM
General Information
- Last Activity
- 09-26-2023 11:03 PM
- Join Date
- 12-21-2005
- Referrals
- 2
15 Friends
Showing Friends 1 to 10 of 15
-
Views: 498
Updated:05-31-2010
-
Views: 839
Updated:07-05-2009
-
Views: 587
Updated:07-05-2009
- Number of Photos
- 7
- Number of Comments
- 0
- Number of times photos viewed
- 9,956
- Disk space used
- 2.4MB
- Last Photo Uploaded

dsc-0002
- Last Comment Posted
- Never