Big Sale "Go Fast Goodies" Included

[Mario]

Making Room, Buying New Stuff, etc.

Unless it says shipped, shipping isn't included. If it does say shipped, it's to the lower 48 states.

Pics of some things can be found in my gallery.

Alabama man Header. Very low Mileage. Drilled for EGT Probe (Included, brand new however I'm not sure if it's the gauge that's bad or the probe) $350 Shipped.

NOS Nitrous dry kit. Most or almost all of a NOS dry shot kit. Full bottle, lines, solenoids and single fogger. (You will need wiring and switches)If it has to be shipped, bottle wiil be emptied unfortunately. However if you pick it up/meet up somewhere, you get an added bonus. (Bottle is off of Angelo Taylor's Old Blue GLH if that hold's sentimental value to anyone) $250
http://i7.photobucket.com/albums/y271/braxx/DryKit.jpg

Super 60 Turbo. Turbo has been ran for no more than 5,000 miles. It's a Turbonetics unit. Has the .63 A/R Turbine Housing. Chrysler style flange.
It's still on my car, however I can pull it in about 30 min.
It does not have the polished compressor housing. So it looks factory in your engine bay. Swingvalve, turbo lines, and wastegate actuator are not included. However the purchaser has the option to buy the TU 3" Swingvalve, Large Can Wastegate Actuator, and SS Braided lines. I will not sell any of the accesories without the turbo. $500, or $850 for everything.

FM Heavy Duty A413 Rebuild Kit. Brand new. Everything that comes in the Forward Motion Kit. Lists for $245. $200 Shipped.

1989 1 Piece Shelby CSX Valve Cover. Great Shape $240 Shipped

TIII Intake: Ported and Powdercoated blue. $200 OBO
http://i19.photobucket.com/albums/b184/mariospeedwagon/Werd/intake_manifold.jpg

- Complete 85' T1 Engine (Turbo, Manifolds, Pan, etc. etc.) Has the Bathtub head and the beefy rods. Note: The 85' Engine should be rebuilt. It was pulled from a junkyard about 5 years ago and never ran since. $100

- Early T1 Shortblock with forged 2.2 crank, forged T2 Rods, and T2 Pistons. $150 (Needs rings)

- Bare 287 "G" Head (Has springs and valves, but they are corroded. Head needs to be cleaned and rebuilt) $40
http://i19.photobucket.com/albums/b184/mariospeedwagon/Werd/2.jpg
http://i19.photobucket.com/albums/b184/mariospeedwagon/Werd/1.jpg

- 782 Head. Complete. Came off of a running car, but the car burned oil. Should be cleaned/rebuilt. $40

Garrett T1 Turbos (Cores, May be good, prob. not) $30 Each.

89' T1 One Piece Intake $25

Early T1 Intakes, $5 Each

1 Piece Style Valve Cover. Powdercoated gloss black. Polished Letters. $70 Shipped (Pics can be found here http://www.turbo-mopar.com/forums/showthread.php?t=1839)

Common Block Main Caps and Bolts (From Gary Donovan if that means anything to you guys) $15

- 2-Door Shadow ES Silver Ground Effects. $40, NO SHIPPING (Pics can be found here: http://www.turbo-mopar.com/forums/showthread.php?t=5952 Half the money goes to Bryan Cordes BTW)

- R/T A-568/A-523 Shifter Cables $55 Shipped
- R/T A-568/A-523 Shifer $30 Shipped

More to come I'm sure.

Cash/Money Order Preffered. PayPal is okay too.

All REASONABLE offers considered.

All Trades Considered.

Tons more parts, just ask.

[Mario]

Anyone interested in the 85' TI Parted out?
Also, any interested in a 420A head with about 60K miles. Needs cams.

If you're interested in either, let me know asap.

Most of this stuff is going to go on ebay where it will more than likely go for a decent amount more than my asking prices here.

[Mario]

Valve Cover off to ebay: http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&ih=019&sspagename=STRK%3AMESE%3AIT&viewitem=&item=290060270256&rd=1&rd=1

[Mario]

Bump...

[Mario]

AB Man header dropped to $300.
S60 with lines, Large Can WGA, and TU 3" Swingvalve now for $800.

Also check my other thread for a deal on a 3" Downpipe.

More Parts

Brand New Set of +40 Injectors: $130
Used Set of +40 Injectors: $100

K&N Air Filter. 2.25 OD. It's a small short filter. $35

More to come. I'm clearing lots of stuff out of here.

I'm guessing this is the worst time of the year to sell this stuff?

[Mario]

1989 Shelby Valve Cover is gone! Thanks if it was someone on here that used the buy it now option. :thumb: It's going out tommorow morning.

[Mario]

8.5MM Magnecore Wires. $35 Shipped. One wire doesn't seem to click all the way.

[ShelGame]

Anyone interested in the 85' TI Parted out?
Also, any interested in a 420A head with about 60K miles. Needs cams.

If you're interested in either, let me know asap.

Most of this stuff is going to go on ebay where it will more than likely go for a decent amount more than my asking prices here.


How much do you want for the 420a head? Shipping not necessary (I'm in town)...

[Mario]

$100.

[Skibbe]

I'm interested in the Super 60 turbo with 3" swingvalve, etc.

Do you have any interest in a Turbonetics 60-1 HiFi w/ Stage 3 .63 a/r, standard bolt pattern hybrid in trade? I'm re-evaluating my needs, and think it's too much turbo for me. This was in Moparboyy's 11 sec GLHS and I believe it's the same as JT's Daytona and Tom's 10 sec SC.

[Mario]

I would but I'm hooked on the GT3076R. That's the turbo I want.

[Garret]

Still have those wires?

[Mario]

Bump.

[Mario]

To The Top.

[Mario]

Offers?

[Mario]

Bump..

[Mario]

Bump.

[Mario]

Bump.

[Frank]

89' T1 One Piece Intake, say $30 shipped cheaply?

[Mario]

I'd have to go weigh it and check....unless you know the weight already.

[Frank]

I'd have to go weigh it and check....unless you know the weight already.

K. I am not in a hurry anyway. I am just buying it to cut it apart and try some methods I came up for making these things awesome.

[moparman76_69]

Alabama man Header. Very low Mileage. Drilled for EGT Probe (Included, brand new however I'm not sure if it's the gauge that's bad or the probe)

got any pics of this?

[Mario]

In my Gallery.

[moparman76_69]

pm sent