MiniVan Parts Wanted

[ajakeski]

I need the following interior parts for my 1989 Voyager:

Dashboard center stack door. I need the a wood grained one with a good latch so it stays closed

Driver's door inside handle trim bezel without broken tabs.

Four seat hook covers for the floor so I can keep things out of the seat hook holes. Gray preferred, but I do have paint.

[martin kolner]

the seat covers or escutcheons are here

which ones do you need?

4314 742 AR STRIKER and BOLT, Seat Retension Front (Use 6500927 Nut)
2 AR SCREW, (8-15x1) (Not Serv.)
3 ESCUTCHEON, Seat Hold Down (Short)
S657 FC5 AR Blue
S657 GR8 AR Red
S657 EK3 AR Almond
S657 CS8 AR Charcoal
4 FLOOR PAN, (Reference)
5 4337 594 AR STRIKER and BOLT, Seat Retension Rear
6 FILLER, Rear Floor Striker, 5 Passenger (Not Serv.)
7 COVER, Seat Escutcheon 7 Passenger
S655 FC5 AR Blue
S655 GR8 AR Red
S655 EK3 AR Almond
S655 CS8 AR Charcoal
8 ESCUTCHEON, Hold Down (7 Passenger) (Long)
w/112" Wheelbase
S656 FC5 1 Blue
S656 GR8 1 Red
S656 EK3 1 Almond
S656 CS8 1 Charcoal
w/119" Wheelbase
S688 FC5 1 Blue
S688 GR8 1 Red
S688 FK3 1 Almond
S688 FS8 1 Charcoal
9 6501 269 AR NUT and WASHER (Use 6500927 For # 1 Bolt) ***

I have a good assortment of these covers NOS or used in lots of colors

4460655 is the upper console door

4184790 is R/L door handle bezel I have these NOS or used

www.arizonaparts.com

[ajakeski]

I popped one out to measure it and saw that Chrysler knew I would need these 25 years after the van was built. The back of the cover is embossed with" Order additional parts form dealer 4248520"

I need four. It's a short wheelbase van.

[martin kolner]

4248520 is the casting # for S655XXX XXX=color code

I have these

S655CB5 blue (11)
S655CM6 red (3)
S655CT8 brown (30)
S655DT5 tan (12)

the above fit 1984-85 minivan....part is the same but the colors are different

( )= QTY all are NOS 4.00 each plus shipping

www.arizonaparts.com (http://www.arizonaparts.com)

[Sgt Craig]

I need the following interior parts for my 1989 Voyager:

Dashboard center stack door. I need the a wood grained one with a good latch so it stays closed

Driver's door inside handle trim bezel without broken tabs.

Four seat hook covers for the floor so I can keep things out of the seat hook holes. Gray preferred, but I do have paint.

Ill check the van I purchased this weekend

[going4speed]

Do you know Doc Brown or Marty? haha :eyebrows:


I popped one out to measure it and saw that Chrysler knew I would need these 25 years after the van was built. The back of the cover is embossed with" Order additional parts form dealer 4248520"

I need four. It's a short wheelbase van.

[ajakeski]

Covers and door handle bezel have been found. I'm still looking for a good console door.

[ajakeski]

I haven't had any luck finding a good console door, so I took mine apart to see if it's repairable.

Quite the Rube-Goldberg design inside there. There's a few plastic pieces that work in concert to release the latch. One piece has (had) a pivot rod cast onto each end and both rods were long gone, broken.

3D printing to the rescue again.

The new part looks like a match and seems stronger than the original. I'll try it tomorrow to see if it works.

[turbovanman²]

Nice. Those 3D printers are going to be life savers. :nod:

[rare_ram]

I took two of the doors to make one working one.

[ajakeski]

I took two of the doors to make one working one.


It seems like it wasn't Chrysler's best design. Probably was designed by a new guy or someone counting his days.

[1991SpiritES]

It seems like it wasn't Chrysler's best design. Probably was designed by a new guy or someone counting his days.

The one in my van is hard to open.