Wanted: Fiberride Center Cap (or Fab Ideas)

[cqlink]

Lost one of my fiberride centercaps while driving the other day. If anyone has one, has a link to one or a fabrication idea, please advise.

Thanks!

[glhs727]

Lost one of my fiberride centercaps while driving the other day. If anyone has one, has a link to one or a fabrication idea, please advise.

Thanks!

I saw some on ebay recently

[Turbo SOB]

I need a full set of 4. I'm working on turning some out of aluminum billet stock. I picked up a 6" long bar of 2 1/4" for $17. I'll let you know how it goes.

[omniac]

I saw some on ebay recently

http://www.ebay.com/itm/NOS-1989-Shelby-CSX-Gold-Fiberide-Wheel-Center-Cap-Dodge-Turbo-VNT-T-IV-/301604496507?vxp=mtr&nma=true&si=rSixjPvDE6kPdrPmAiSNBzbUJ54%253D&orig_cvip=true&rt=nc&_trksid=p2047675.l2557

[Fox]

the caps themselves aren't that rare just the gold colored ones, you can usually find a few silver ones on eBay easy

[cqlink]

Thanks. I'm not really up to paying $65+ for ONE center cap. Let me know how the aluminum billet stock works out. If you're successful, I'll buy a couple off of you.

[martin kolner]

4284004
X086KD2 quartz
X086GW7 white
X086LW2 gold
4284012
4284702
4472115

all of these will work, some are aluminum and others are plastic.

some of these numbers are casting numbers

[Turbo SOB]

The aluminum center caps (pizza wheel, centurion, etc.) do not work. They are too small and fit too loosely. The O.D. of the fiberide cap is between 2 1/16" and 2 1/8". The aluminum caps are closer to 2".

The lowest cost I could scrounge up for the plastic center caps was $20 each, and I think that was from Martin. My upper limit is $5 each.

So, so far I'm into this project for $17 and I think I'll be able to make 8 of them. I'll need some time though. This is a project that I work on during breaks and lunches.

Thanks,
Jeff

[Turbo SOB]

So, here's what I have so far. I found some retaining clips in the junk bin at work. They work fine. Now I just need to decide if I'm going to bevel the face a bit.

I'm still only into this for $17 (plus my time).

I don't know why, but the pictures I include always seem to disappear. Here they are again.

http://www.turbo-mopar.com/forums/attachment.php?attachmentid=54810&stc=1http://www.turbo-mopar.com/forums/attachment.php?attachmentid=54811&stc=1http://www.turbo-mopar.com/forums/attachment.php?attachmentid=54812&stc=1http://www.turbo-mopar.com/forums/attachment.php?attachmentid=54813&stc=1http://www.turbo-mopar.com/forums/attachment.php?attachmentid=54814&stc=1

[Turbo SOB]

Project complete. I am not completely satisfied, but it's good enough for now. The paint ended up being thicker than I was expecting, so they look like they sit a bit proud.

http://www.turbo-mopar.com/forums/attachment.php?attachmentid=54815&stc=1http://www.turbo-mopar.com/forums/attachment.php?attachmentid=54816&stc=1http://www.turbo-mopar.com/forums/attachment.php?attachmentid=54817&stc=1http://www.turbo-mopar.com/forums/attachment.php?attachmentid=54818&stc=1http://www.turbo-mopar.com/forums/attachment.php?attachmentid=54819&stc=1http://www.turbo-mopar.com/forums/attachment.php?attachmentid=54820&stc=1http://www.turbo-mopar.com/forums/attachment.php?attachmentid=54821&stc=1

Also, despite everything being Dupli-Color "Hyper Silver" the caps and wheels look totally different. What a waste of paint.

Also, I have 3 1/2" of the billet left over. So, plenty left to do 4 more.