omnigoestohell
09-07-2014, 10:52 AM
hey all..
hoping someone can perhaps help here. I have a set of eagle H beam rods in my T3 GLHS and have a rod bearing that looks slightly marginal that I'd like to replace --- unfortunately the "notch" on the clevite 77 CB1269P rod bearing is significantly bigger than the notch on the eagle rod. the rod cap notch measurers .115 while the notch on the clevite measures .115mm. the old bearing that was in the car is an unknown brand (to me) but the notch measures .113 so it fit fine. the markings on the old rod bearing seems to say "05507AA" and "234 6M". does anyone have any ideas what those bearings are or if there is some way to make this work short of filing the notch down on the clevite?
http://www.patsauto.com/td/rod/IMG_1015SM.JPGhttp://www.patsauto.com/td/rod/IMG_1029SM.JPG
http://www.patsauto.com/td/rod/IMG_1019SM.JPGhttp://www.patsauto.com/td/rod/IMG_1020SM.JPGhttp://www.patsauto.com/td/rod/IMG_1024SM.JPGhttp://www.patsauto.com/td/rod/IMG_1025SM.JPGhttp://www.patsauto.com/td/rod/IMG_1026SM.JPGhttp://www.patsauto.com/td/rod/IMG_1028SM.JPG
http://www.patsauto.com/td/rod/IMG_1015.JPG
http://www.patsauto.com/td/rod/IMG_1019.JPG
http://www.patsauto.com/td/rod/IMG_1020.JPG
http://www.patsauto.com/td/rod/IMG_1024.JPG
http://www.patsauto.com/td/rod/IMG_1025.JPG
http://www.patsauto.com/td/rod/IMG_1026.JPG
http://www.patsauto.com/td/rod/IMG_1028.JPG
thanks
hoping someone can perhaps help here. I have a set of eagle H beam rods in my T3 GLHS and have a rod bearing that looks slightly marginal that I'd like to replace --- unfortunately the "notch" on the clevite 77 CB1269P rod bearing is significantly bigger than the notch on the eagle rod. the rod cap notch measurers .115 while the notch on the clevite measures .115mm. the old bearing that was in the car is an unknown brand (to me) but the notch measures .113 so it fit fine. the markings on the old rod bearing seems to say "05507AA" and "234 6M". does anyone have any ideas what those bearings are or if there is some way to make this work short of filing the notch down on the clevite?
http://www.patsauto.com/td/rod/IMG_1015SM.JPGhttp://www.patsauto.com/td/rod/IMG_1029SM.JPG
http://www.patsauto.com/td/rod/IMG_1019SM.JPGhttp://www.patsauto.com/td/rod/IMG_1020SM.JPGhttp://www.patsauto.com/td/rod/IMG_1024SM.JPGhttp://www.patsauto.com/td/rod/IMG_1025SM.JPGhttp://www.patsauto.com/td/rod/IMG_1026SM.JPGhttp://www.patsauto.com/td/rod/IMG_1028SM.JPG
http://www.patsauto.com/td/rod/IMG_1015.JPG
http://www.patsauto.com/td/rod/IMG_1019.JPG
http://www.patsauto.com/td/rod/IMG_1020.JPG
http://www.patsauto.com/td/rod/IMG_1024.JPG
http://www.patsauto.com/td/rod/IMG_1025.JPG
http://www.patsauto.com/td/rod/IMG_1026.JPG
http://www.patsauto.com/td/rod/IMG_1028.JPG
thanks