2 piece upper plenums

[lengel]

Seems to be some interest in these upper plenums. I would need to sell 10 plenums to do this batch. They will be $325 + shipping, and I will need a $120 non refundable deposit for all 10 plenums to get started. When I receive 10 deposits the aluminum will be ordered. Once the aluminum is delivered, I will give my self 3 months to complete all orders (could be sooner but no later). The Buyer will have 30 days to pay the balance upon completion. After 30 days the plenum will be sold to recover my costs. These will all be the same design as the plenums I did in the past. The buyer will be responsible for adding any vacuum/sensor ports. The plenum has a .25" wall so it can be drilled and tapped anywhere on the plenum. So lets see a show of hands of who wants one. Only post if you are 100% committed to buy one. Here are some pics if you have not already seen them. After we have 10 committed buyers I will post deposit info. I will be stating this same group buy on the other site, so if you post here dont post over there. This will just keep me less confused.

1: kurt (1) paid Shipped
2:iTurbo (1) paid Shipped
3:glhs727 (3) paid Shipped
4: Dan H (1) paid Shipped
5:boboli (1) paid Shipped
6:nvysion (1) paid
7:mrboostman (1) paid Shipped
8:tthcare (1) paid Shipped
9: zin (1) paid Shipped
10: wheming (1) paid Shipped
11: OMNI 840 (1) paid Shipped
12: Omnidaddio (1) paid Shipped
13: Punish'nRice (1) paid Shipped
Thanks Adam

http://i379.photobucket.com/albums/oo237/bethany017/photobucket-7455-1359919545355_zpsd4fa5aec.jpg
http://i379.photobucket.com/albums/oo237/bethany017/photobucket-7917-1359919606160_zps790019df.jpg
http://i379.photobucket.com/albums/oo237/bethany017/photobucket-7013-1359841615171_zpsa72344db.jpg
http://i379.photobucket.com/albums/oo237/bethany017/photobucket-4061-1359841586279_zps6216c403.jpg
http://i379.photobucket.com/albums/oo237/bethany017/photobucket-2687-1359841559105_zpsa29ba74f.jpg
http://i379.photobucket.com/albums/oo237/bethany017/photobucket-8482-1359841527586_zps36c19ec4.jpg
http://i379.photobucket.com/albums/oo237/bethany017/photobucket-7047-1359840968697_zps8f0bab69.jpg
http://i379.photobucket.com/albums/oo237/bethany017/photobucket-7763-1359840936202_zps9e4df6b3.jpg

[krut]

I'll take one.

[iTurbo]

I'll take one too, looks awesome! Adam, will I be able to use this with the ported 58mm throttle body I got from you a while back? I also have an aftermarket FWDP fuel rail...will that work OK? Will porting the lower runners be necessary or optional?

[krut]

No one else interested? Boo.

[lengel]

I'll take one too, looks awesome! Adam, will I be able to use this with the ported 58mm throttle body I got from you a while back? I also have an aftermarket FWDP fuel rail...will that work OK? Will porting the lower runners be necessary or optional?

Thanks Jeremy! Yes they are made to use a 58mm TB. I dont see why a FWD rail wouldnt work, but maybe Cindy could answer that for sure. You would see the best gains by porting the lower. Steve Menegon just got done / or is just finishing up porting some from the last ones I did. If we get thses going, I would get ahold of him.

Thanks Adam

[glhs727]

Thanks Jeremy! Yes they are made to use a 58mm TB. I dont see why a FWD rail wouldnt work, but maybe Cindy could answer that for sure. You would see the best gains by porting the lower. Steve Menegon just got done / or is just finishing up porting some from the last ones I did. If we get thses going, I would get ahold of him.

Thanks Adam
I'll check on the rails when I get back from vacation on the 12th. Adam, I'll take 3 more if that helps the group buy!

[BOOSTIFIED]

Put me down for one, I'll send payment next friday as when i get paid.

[boboli]

Alright, I will take one. Don't want to miss out on getting one of these again.

[BOOSTIFIED]

Can I add one of those fuel rails to my order?

[nvysion]

I want one

[krut]

Cindy, did you ever get into looking to see if your rail fits with this upper? I'm curious. Thanks

[wowzer]

Cindy, did you ever get into looking to see if your rail fits with this upper? I'm curious. Thanks

curious also.

[krut]

Any news?

[nvysion]

Bump for some news

[minigts]

I'm in. Don't have to ask me twice! :)

[iTurbo]

Woot! So there are at least two more interested users in this. I know all too well how it's best to have patience in a product like this, especially considering the niche market of turbo Mopardom. More people getting on this = better.

Looking forward to this. If it takes two months or two years that is OK with me considering the quality of Adam's work which I can vouch for with the other parts I've gotten from him over the last few years. I've bought TIII timing belt tensioners (and idlers pullies!), TIII intake manifold flanges, gauge pods for Spirits, Maserati 16v thermostat housings, and CNC ported 58mm throttle bodies from Adam and have been VERY happy. We are talking no-holds-barred quality work here. If you are considering a nice intake for the TII you are seriously missing out if you don't get in on this.

I'm especially thankful that Adam made the TIII timing belt tensioners because they are now unavailable from the dealership and the ones Adam makes are way better than stock. This guy is capable of great things and he is supporting our hobby big time with the time and work he is investing in these parts!

[lengel]

Thanks for the interest guys, and nice words. If we do get 10 for the groud buy, I would not be able to start these till late fall/winter. This is due to work getting VERY busy. So if that still works for you guys, I will start taking deposits once we reach 10 people. That way I will have all the aluminum, and can start asap once work starts slowing down a bit.

Adam

[mrboostman]

Hi,
Can you put me on the list for (1) please?

[wheming]

Being out of the loop for a while, could someone point me to some usage data/testing.
I'm interested in one, thinking MeanMini might need it with the new turbo and TU header.

Also, if I were interested in one for (hypothetically speaking) a rwd application, could the TB flange be mounted on the opposite side? It appears everything is symetrical.

[krut]

Any news on fuel rail fitment??

[glhs727]

yes, our rail fits! so if you already have an FWD rail, you are fine. In addition I had some other rails made a long time ago, turned out the way we did the regulator mount, it interfered with the stock 2 piece upper, so we ended up putting them aside. I pulled one out of the box and it fits great, So I will put them On my site as a fuel rail for the lengel intake and put them on sale for $119 if anyone wants one! remember all out 2 piece rails will fit either the stock lengel intake, but the lengel rail will ONLY fit the lengel intake! http://i216.photobucket.com/albums/cc7/srt403/029_zpsd47cd836.jpg

[wheming]

Do you have at least 10 so we can all get one? Or is there going to be a fight??? ;)

[tthcare]

Looks like between the 2 sites the count is there

[iTurbo]

Thanks for the pic and info Cindy.

I don't mind waiting. I'm building both a TI and TII right now and don't think I'll need the intake until late this year anyway.

[zin]

I'll throw my hat in the ring. I'd like to get mine with the rear "end cap" not welded on if that's not too much of a hassle.

Mike

- - - Updated - - -

I'll throw my hat in the ring. I'd like to get mine with the rear "end cap" not welded on if that's not too much of a hassle.

Mike

[lengel]

Being out of the loop for a while, could someone point me to some usage data/testing.
I'm interested in one, thinking MeanMini might need it with the new turbo and TU header.

Also, if I were interested in one for (hypothetically speaking) a rwd application, could the TB flange be mounted on the opposite side? It appears everything is symetrical.

Yeah the end caps can be welded on either side, so thats no problem. I would just have to know how you want it before welding


I'll throw my hat in the ring. I'd like to get mine with the rear "end cap" not welded on if that's not too much of a hassle.

Mike

- - - Updated - - -

I'll throw my hat in the ring. I'd like to get mine with the rear "end cap" not welded on if that's not too much of a hassle.

Mike

Yeah thats no problem.

- - - Updated - - -


Looks like between the 2 sites the count is there

Yes it looks like we reached 10. I will be sending PMs to every body with in the next week, and once we get all the deposits I will order the aluminum.

Thanks for all the interest!

Adam

[nvysion]

Adam,
I didn't receive your email, have you sent them ?

[wheming]

Adam, can you please add me to the list for (1) built normal?
I better do this now so I'll have one when I need it. Thanks.

[minigts]

I'm on the list too. :)

[krut]

Any news?

[zin]

Yeah, holidays are coming up, I don't want to find out that the money I set aside got used for "an emergency" like X-mas gifts, etc!

I'd be ok with pre-paying the whole amount, just so I know it's handled and won't have to flake later when I find the funds highjacked.

Mike

[lengel]

Yeah, holidays are coming up, I don't want to find out that the money I set aside got used for "an emergency" like X-mas gifts, etc!

I'd be ok with pre-paying the whole amount, just so I know it's handled and won't have to flake later when I find the funds highjacked.

Mike

LOL! No worries about that. When someone trusts me with there hard earned cash, I take that very seriously. Once I have the metal these will be my priority! I have been around here for a little and plan on keeping it that way! I look forward to starting this project and I think every body will be happy with them.:nod:

[lengel]

PMs have been sent to every body on the list. If your on the list and didnt get a pm, please let me know. If your not on the list and would like one, speak up now. Once the metal is ordered I will not be adding anyone else to the list. Thank you to every body for your interest in these. I look forward to starting this project!

Adam

[boboli]

deposit sent

[iTurbo]

Deposit sent.

[krut]

Deposit sent.

[nvysion]

same for me.

[omni_840]

Is it too late to get in on this GB?

[lengel]

Is it too late to get in on this GB?

I didn't order the aluminum yet, so your not too late. I will send you the same pm I sent everyone else.

adam

[zin]

Done and Done!

Mike

[tthcare]

Sent my deposit. Will a 52 mm throttle body bolt up?

[wheming]

I didn't order the aluminum yet, so your not too late. I will send you the same pm I sent everyone else.

adam

Don't forget to add his "late to the party fee." :D

[lengel]

Sent my deposit. Will a 52 mm throttle body bolt up?

Yeah a 52 will work.

[omni_840]

Don't forget to add his "late to the party fee." :D


Hey now :p

Better late than never!


Deposit sent and Thanks Adam for making these for the community:nod:

[mrboostman]

Deposit sent.
Thanks.

[lengel]

Two more deposits to go then we can order the aluminum.

[wheming]

What's the balance now? I could have just paid in full too.

[lengel]

What's the balance now? I could have just paid in full too.

Thats no problem. Just PM me your zip and I will get you a total shipped balance.

[lengel]

Guess I will make a dead line for deposits or anyone else that wants one. Dead line is Nov. 10th Aluminum will be order on the 11th.

Adam

[looneytuner]

Yeah a 52 will work.
Is there more than one 52 mm tb? Or do I just have to relocate the Vacuum nipple on the van tb?

[lengel]

Is there more than one 52 mm tb? Or do I just have to relocate the Vacuum nipple on the van tb?

I know there are a few different 52mm TB castings. They all have the same bolt pattern, but I am unsure of the vacuum nipple. As long as your 52 has the vacuum nipple going straight up it will work fine. You can pick a 52mm TB very cheap ($20 or less) if yours will not work.

Adam

[lengel]

This is the last day to get in on the group buy. Ordering aluminum tomorrow.

adam

[GLHNSLHT2]

Any 3.3 52mm TB is the same as the Turbo 46 as far as vac nipples. It's the 3.0 52's that have a different vac arrangement

[lengel]

Aluminum is on its way for the end cap. TB flange, and plenum tube. Im still waiting on a quote for the aluminum for the plenum flange. I will be calling them tomorrow.

Adam

[lengel]

I got all the plenum flange aluminum on Thursday. Its all cut to length and ready to machine.

[omnidaddio]

Good news. Is it going to be Merry Christmas to me, this year?

[lengel]

47805
Making progress! I got all the plenum flanges done, and all the end caps.

[minigts]

47805
Making progress! I got all the plenum flanges done, and all the end caps.

I know I'm going to regret backing out of this deal. :( Looks incredible Adam, love your work!

[zin]

I'm glad I paid up front, there will always be something else you "should" spend that money on somewhere down the line, but funny how, if it ain't there, you always seem to manage in the end ...

Mike

- - - Updated - - -

I'm glad I paid up front, there will always be something else you "should" spend that money on somewhere down the line, but funny how, if it ain't there, you always seem to manage in the end ...

Mike

[Punish'nRice]

Any chance for a late comer to get one of these?

[lengel]

47970
Plenum end caps

[lengel]

47972
1/2 way done on the TB flanges!

[iTurbo]

Very nice. Great job Adam, I wish everyone put hard work and dedication into stuff they built like this. Where I work, I try as hard as I can to make the nicest tile shower enclosures I can, even though the owner doesn't seem to care one way or the other. It doesn't matter though, as long as you keep your own standards high and keep doing better all the time.

[Punish'nRice]

Looking good. Thanks for adding me to the group buy. :)

[lengel]

4805048051
I got all the TB flanges done today, and cut all the plenums, so they are ready to start machining. Getting there!

[lengel]

Got all the plenum tubes done this past week. Today all the pieces were taken down to Brian's shop to get welded.

[Punish'nRice]

Got all the plenum tubes done this past week. Today all the pieces were taken down to Brian's shop to get welded.

Saweet!! shouldn't be long now. :)

[lengel]

Plenums are done! Picked them up from mr. Slowe's shop today, and he did a great job on them. Thanks Brian! I will be sending pms to everybody tonight or tomorrow.

Thanks Adam
http://img.tapatalk.com/d/14/01/12/ne9e2eqy.jpg

[iTurbo]

Payment sent. Thanks Adam.

[j4278h]

If someone backs out of one, let me know.

[wheming]

Btw, now that we are so close to delivery, was there a thread on installation and what is required?
It sounded like my 52mm TB would be ok, but was there a need to change cables?
Planning now to use this on MeanMini.

[omni_840]

^^ Good idea Wayne

BTW Payment sent!

[lengel]

Btw, now that we are so close to delivery, was there a thread on installation and what is required?
It sounded like my 52mm TB would be ok, but was there a need to change cables?
Planning now to use this on MeanMini.


^^ Good idea Wayne

BTW Payment sent!

I personally never installed one, but the only things I can think of that will have to be done is sensor/vacuum holes drilled and tapped, run your intercooler piping over to the new TB location, maybe lengthen AIS and TPS wires. I dont know about the throttle cable. I wouldnt see why it couldnt just be lopped around. It should be long enough since the TB is closer to the fire wall.

Adam

- - - Updated - - -

I will be shipping all the plenums after work for the people that are paid in full. I will be sending everybody a pm tonight with tracking info.

Thanks Adam

[lengel]

Paid plenums have been shipped, and tracking #s have been sent.

Adam

[nvysion]

Money sent

[wheming]

Got mine! :thumbup:

[tthcare]

Thanks Adam
Received mine today.
I would not hesitate to buy something from you again. I waited a longtime for a part that had to be manufactured from a vendor. You were true to your word on timing.

[krut]

Thanks for doing this group buy! Keep us posted on anything else that may be made!
Thanks.

[iTurbo]

Got mine today, thanks Adam!

[lengel]

Thanks for the positive feed back guys!

[lengel]

If anyone else would one of these PM me

Adam

[zin]

Got mine today, pictures just aren't the same as having it in your hands, so far as appreciating the quality of these pieces!

Being a cheap skate, it wasn't easy to fork out the $$, but it is definitely money well spent!

Mike

[boboli]

Got mine today. It truly is beautiful. I may just keep it on a shelf or maybe a display motor on a stand. Great packing by the way. Box was a little messed up but there was so much interior padding that I had to dig around till I found it. Thanks again. A great part.really couldn't be happier. If there are any left and you want one, you will not be disappointed. Plus you won't have to wait for them to be manufactured

[lengel]

Thanks for the feed back guys.

Anybody have a pic of one installed? Would someone be able to take a look at the ais and tps wires to see if they would need to be lengthened or not ?

Thanks Adam

[iTurbo]

I was just comparing your upper plenum to a stock 2-piece intake in my 2nd bedroom (the staging/museum room). I would be surprised if the TPS/AIS wiring would need to be lengthened at all. That is with using the 58mm CNC-ported Chrysler throttle body I also got from lengel (which fits soooo perfect!)

I wish I could post pics of it installed, but I'm not that far yet. However I see no issues regarding the TPS/AIS wiring. The plenum appears to sit a tad bit lower, and the throttle body will face the driver's side, but the overall throttle body is so close to stock... Should plug right in!

[lengel]

Thanks Jeremy!

[Johnny]

Any installs yet?

[krut]

I should be doing mine soon.

[Punish'nRice]

Has anyone ever use the Turbos Unleashed fuel rail with this intake?

[wheming]

I know this thread has been pretty quiet lately.
But, I was looking at my plenum and checking the fit of my 52mm TB and found the TPS plug points directly to the plenum. No way the plug will attach.
So, is the 58mm TB different in that regard?
Is there a TPS sensor that works but has a 90 deg plug?
Or is the plug simply installed backwards to make this work?

[JohnnyIroc]

I know this thread has been pretty quiet lately.
But, I was looking at my plenum and checking the fit of my 52mm TB and found the TPS plug points directly to the plenum. No way the plug will attach.
So, is the 58mm TB different in that regard?
Is there a TPS sensor that works but has a 90 deg plug?
Or is the plug simply installed backwards to make this work?
IIRC the mini van tps are at a 90 degree

[GLHNSLHT2]

you just flip the TPS around.

[wheming]

you just flip the TPS around.

I was hoping that! (When i said install plug backwards, i meant TPS.) Just wasn't sure if it would be properly zeroed.
Thanks!

[lengel]

Yup as said, just flip it around. Also as said some of the mini vans had them 90deg. I think they were mostly on the 3.0 mini vans.

[nvysion]

I would like to see pics showing where holes has been drilled for the vacuum noses.
There must be enough thickness for tapping and I don't want to make a mistake.

[Punish'nRice]

Has anyone ever use the Turbos Unleashed fuel rail with this intake?

Anybody??? :)

[JohnnyIroc]

4978849789

[Johnny]

Looking at installing this in the next week.
The cables for the throttle and the trans usually hang on a bracket.
There seems to be no way to hang this bracket...and even if it could,
the angle being 90 degrees off seems to make an issue.

AND of course the question above, holes for vac lines?...anyone do this yet?

- - - Updated - - -


4978849789

Did this get completed? Any advise or custom work that you could enlighten us with?

[lengel]

There may be some modification needed to the cable bracket if you run a silicon 90 right on the TB. I seen one guy use a straight coupler then a mandrel 90 bend. It didn't look like he needed to modify the bracket. As for the vac/sensor ports. that is left up to the end user to put in where needed. Any place on the plenum will be fine for this since the pieces used are .25 thick. So just drill and tap where needed.

[contraption22]

If you're not using a kickdown cable you can slice a bit off the throttle bracket to clear the 90

[GLHNSLHT2]

Using an 88+ turbo or 3.0 V6 cable and bracket should clear a 90 no problem.

[lengel]

If you're not using a kickdown cable you can slice a bit off the throttle bracket to clear the 90


Using an 88+ turbo or 3.0 V6 cable and bracket should clear a 90 no problem.

Thanks for the info guys!

[Johnny]

Guess I'll test fit it and see what I come up with.

[JohnnyIroc]

sorry nothing has come with mine yet, on an l body in one spot a have an inch of clearance from the firewall. so its going to be tough to decide where to put vaccum ports.
i want to get the car up and going so i think this will be a project for later in the year

[wheming]

I made it as far as glass beading mine today in preparation for paint...

Sorry I'm so slow. Hope to have mine installed on Mini in the next month or so.

[Johnny]

I installed mine today. Will get photos after the throttle body is on tomorrow.

[Johnny]

While in progress....

[krut]

Looks to be the same way I did it - tapping on the back and using street ell's.
No more ugly vacuum block!

[Johnny]

Well I have one on the rear. I will change that "someday".
Hard to find non-brass fittings.

[wheming]

Johnny you might want to break off that pipe worm before you button things up.
At a later time if that piece of thread shaving breaks off, it'll end up in a cylinder.

[Johnny]

I see that there... teflon tape will hurt something?

[Punish'nRice]

Looks good. Thanks for posting the pics. Who's fuel rail do you have?

[Johnny]

Got it from TurbosUnleashed.

[wheming]

I see that there... teflon tape will hurt something?

Oh... it looked like a piece of aluminum from drilling or threading.

[JohnnyIroc]

is this on your consouler johnny?

[Johnny]

Yes it is the Consulier.
Got the throttle body gasket today so installed it.
The throttle cable bracket is for an auto, and do not need that part so
cut off the too long part so it would fit with my 90 degree silicone elbow.
See photo F for bracket too long....photo C for the photo with the bracket cut to fit.

But as you can see, now the air box is in the way. (photo D)

Also an issue on my car ....(photo E) this set up makes the need to extend the throttle body plugs.

Only thing I am not sure of is how to deal with the air filter.

[lengel]

Wow looks good Johnny! Looks like two bends welded together should get you over to the air box.

[contraption22]

Yes it is the Consulier.
Got the throttle body gasket today so installed it.
The throttle cable bracket is for an auto, and do not need that part so
cut off the too long part so it would fit with my 90 degree silicone elbow.
See photo F for bracket too long....photo C for the photo with the bracket cut to fit.

But as you can see, now the air box is in the way. (photo D)

Also an issue on my car ....(photo E) this set up makes the need to extend the throttle body plugs.



Nice work!



Only thing I am not sure of is how to deal with the air filter.



Roof scoop!

50393

[zin]

Roof scoop!

50393

Always did like this idea, kinda F1-ish...

Scoop to a basic panel style K&N, might not be too hard to fab up, especially if you could use an existing scoop from the MR2 or Fieros, no idea on cost though...

Mike

[GLHNSLHT2]

find a 1990 8v turbo airbox to use instead.

87-89 airbox

https://scontent-a-sea.xx.fbcdn.net/hphotos-ash2/t1.0-9/1012019_3759735927345_1088977839_n.jpg


90+ airbox

https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-xpa1/t1.0-9/1524813_3760088456158_1976072816_n.jpg


That is if you want to run a factory style airbox. The 90 setup allows you to run a straight pipe to from the i/c to the TB without necking down to go through the airbox. It also has inlets and outlets that have the same area as a 3.5" diameter pipe so it flows more air. Sounds like you put a big cone filter on the car with this setup.

[GLHNSLHT2]

Also why are you running a 52mm TB? I thought these plenums were set up for 58's??? You might also want to find a 52 from a 3.3 V6 (if you don't/can't change up to a 58) as they have the same vac ports as the Turbo's. The 52 with ports in the center bosses are ported vac, where the 52 with a port in the outside boss is true vacuum and the one in the center is ported. Not sure how the GTP is set up vac wise with the TB though.

[GLHNSLHT2]

Nevermind about the airbox, forgot you were running a TU header.

[Johnny]

Also why are you running a 52mm TB?

The stock one is small, so am installing the only larger one I have.
I measured this one and was 53.3...if I remember right.

[GLHNSLHT2]

yea it's what the factory calls a 52mm. There's a couple 58's at the local j-yard.

[Punish'nRice]

I just set mine on & its like 1/2" or less from firewall. Do I have to run solid motor mounts with intake? I'm currently running a mp front motor mount.

[JohnnyIroc]

solid front and rear mounts will be needed for this, i kinda got nervous with how damn close it was to my firewall too.

[Johnny]

I got mine finally working today. Throttle cable did not fit, was too short. Original was 100 inches long and the new one had to be 120 inches long. Used one from a marine shop, with lots of mods. Extending the wiring tomorrow and then test drive. Will take photos.

[lengel]

I just set mine on & its like 1/2" or less from firewall. Do I have to run solid motor mounts with intake? I'm currently running a mp front motor mount.

I would think if your mounts are all in good shape you would be fine, but the poly bushing are the way to go on any modified car in my opinion. Easier on the axles, and better 60'. ;)

[lengel]

I got mine finally working today. Throttle cable did not fit, was too short. Original was 100 inches long and the new one had to be 120 inches long. Used one from a marine shop, with lots of mods. Extending the wiring tomorrow and then test drive. Will take photos.

Nice Johnny! I would love to see a picture of it.

I don't think anyone else will have a cable length issue. On your consulier the TB is farther away from the gas pedal. In a fwd car the TB will be closer to the pedal, so fwd cars should have alittle extra cable.

[Johnny]

I figured that, my own issue to be sure.

[Johnny]

I started the car, fixing a few little issues. Then will button up the rest.

[Johnny]

Got it assembled, running and did a test drive today. It works.

[moparzrule]

Lengel please clear your PM's!

[lengel]

Lengel please clear your PM's!

Sorry I'm on vacation and my vendor membership expired, and I can't figure out how to renew it on my phone. :( LOL!

[moparzrule]

That's fine man I understand. Do you happen to have any of these laying around you can sell?

[lengel]

Sorry I don't have any. If you want one I would make a wanted thread. Someone may have one that they don't need anymore.

[Xtrempickup]

I want a large plenum for my 2 piece also