Megasquirt with wire harness.

[87turbodance]

Date: 07th June 2012
Username: 87turbodance
Full Name: Ryan Loos
City, State, Zip: London, Ontario, Canada
Contact: ryanloos54 at gmail.com
Price: $300obo
Description: Megasquirt 1 Extra with three foot wire harness and upgrades

I have for sale a Megasquirt v 3.0 mainboard with a Ms1 processor installed. I also have a RSAutoSport harness with it that was cut to about three feet long when I removed the MS from my car today. This MS is setup to run a 3.0 with an 18-1 toothed wheel on the crankshaft and a hall-effect crank position sensor. This MS can easily be upgraded to MS2 or MS3 for about $100 for MS2 or $200 for MS3. I build this MS using a kit from the now closed Glen's Garage and it worked very well in my car before I scrapped it today.

I have added three circuits to the proto area of this MS. I have added a universal relay driver circuit that I used to drive a cooling fan relay. I have added a second map sensor for constant baro correction. I have added a circuit to drive the factory tachometer or an aftermarket tachometer.

This board doesn't have any of the VR sensor components installed so the VR sensor input isn't functional. I haven't installed some of the injector flyback components so low-z injector's can't be used without a peak & hold injector driver board installed (I have two of these (drive up to 8 injectors) for sale as well).

This board is setup to drive a single coil driver but could easily be modded to run wasted spark with up to four coils (8 cylinders).

I can provide technical support to the buyer as well.
http://img684.imageshack.us/img684/7360/20120607183201.jpg
http://img705.imageshack.us/img705/2117/20120607183210.jpg
http://img507.imageshack.us/img507/9159/20120607183242.jpg
http://img684.imageshack.us/img684/4293/20120607183415.jpg

[Wiscoballer]

does this come with the wideband as well?

[87turbodance]

does this come with the wideband as well?

no. i don't have a wideband, unfortunately. I never did.

[Wiscoballer]

no computer connect cable either?

[87turbodance]

no computer connect cable either?

It comes with the serial cable but I didn't mention it because it's easy to source.

---------- Post added at 08:15 PM ---------- Previous post was at 08:10 PM ----------

A completed MS1 unit from diyautotune is $350 WITHOUT a wire harness or any extra circuits.

---------- Post added at 08:21 PM ---------- Previous post was at 08:15 PM ----------

I also have two peak & hold driver board for sale hat are assembled. I'm asking $50 each for the peak & hold board.
I have a GM wasted spark block that I have installed the coil driver inside and wired. The unit is incomplete and requires an aluminum plate cut to size and instaled behind the block to the coils can be bolted on. Pictures soon.

I also have extra wiring and relays that will go with the MS as well as some extra parts and components.

I'm going to dig through my junk and see what else I can find.

This MS is wired to work with a hall effect sensor OR the factory 3.0 distributor. I recommend using a toothed wheel on the crankshaft with the factory distributor and single coil setup to begin with.

---------- Post added at 08:22 PM ---------- Previous post was at 08:21 PM ----------

Reasonable offers accepted.

[paduster]

pm sent

[87turbodance]

This MS will also work with the hall-effect sensor in a 2.2/2.5 TBI distributor. One of the peak & hold board that I have for sale can be used with this MS to drive stock turbo low-z injectors.

[paduster]

sold to me