G body parts!!

[Dony409]

Shipping at your cost

AC alternator mounts $20 each
Non AC brackets $15 each
90 Daytona turbo dash w/boost gauge $20
Upper timing belt cover $15
Stock 86 CS coil overs $20 for both (shocks seem good)
Numerous tI parts (manifolds fuel rails harnesses and injectors) $10 each
Numerous 85/86 logic modules $25 each
Daytona trunk carpet (grey) clean decent condition $10
2 87-91 Daytona "bump" hoods ones black ones blue both would need reprinting to be stellar $20 each
1-87 Shelby z tail light $20 for both
84-89 stereo bezel with fog light switch $15
Numerous switches and buttons for wipers and seats $5 each
1st get daytona muffler with tip $15
A couple of valve covers $15 ea
grey Daytona trunk cover rolls decent I will only trade for equal condition blak one

I also am totally parting out a complete 90 Daytona es
And whatever is left of the 88 Shelby z do just ask I might have i

[90TSpirit]

Do you have front seats for this car and are they manual? What color please post a pic and how much including shipping to Groton CT 06340, were are you located?

[Dony409]

I don't wanna crap on you parade but it will cost a fortune to ship them I live in Edmonton Alberta also I cannot post photos from my phone but i you send me you email I'll send you a couple their greyanuap and in pretty good condition. I don't know what shipping would be but I want like $40 for both seats

[90TSpirit]

send a pic of the drivers seat to kenkerttula@yahoo.com are they manual seats?

[Dony409]

Hey sorry I haven't gotten back to you lately what do you thinks the best way to ship the seat would be? And it's still in the car right now cause I don't know how I would ship it and I'll get diemensions and stuff to check at the po for cost tI ship

[Wiscoballer]

got the resistor pack for the climate controls? a blower motor?

[Dony409]

Idk photo me lol

[Wiscoballer]

http://www.partsgeek.com/catalog/1990/dodge/spirit/climate_control/blower_motor_resistor.html
a (http://www.partsgeek.com/catalog/1990/dodge/spirit/climate_control/blower_motor_resistor.html)nd
http://www.partsgeek.com/catalog/1990/dodge/spirit/climate_control/blower_motor.html

[Dony409]

I will have the resistor pack but not the Motor where would the resistor be located?

[Wiscoballer]

in the climate controls I believe

I'll just take the climate controls if you dont feel comfortable

[Dony409]

Well it's your choice it's the same price for just the pack or the hole control it's just shipping will be different I'll see what I can do to get it out and I'll get back to you

[Wiscoballer]

alright, what is the price?

[Dony409]

Oh dear... Me an offer? I am really bad with prices on stuff like this :P

[Wiscoballer]

I can get the resistor pack for 5 + shipping, but I have to install it. For the entire thing, 10+ship?

[Wiscoballer]

can I also get a pic before you ship it?

[Dony409]

Yes and yea

[JohnnyIroc]

daytona hoods do not work 87 -91
90 and 91 are both different
but i know you can use 91 hoods on a 90 or vise versa
but cannot use anything older on either of the 2
87-89 was the same IIRC

[Dony409]

Hey where is this resistor peice located?

[Wiscoballer]

resistor piece should be in the controls, like inside inside. Just sell me the whole controls please... (:

[jackerman]

do you have ac condenser

[TurboII]

HAve a gauge cluster?

[Dony409]

Yup type a couple of peices missing of the blak plastic at the top but isn't noticeable with surround off 206 on the clock

[mopardad1]

Driver's door inner panel?

color?

[Dony409]

Grey missing reflector decently clean and good condition I don't think that would be worth shipping though....

[Lee'sdaytona]

Would you have a front engine mount bracket, that bolts from the block to the frame, that would fit my TI 86 Daytona?
-Lee

[Dony409]

I would but I need it for my 86 lol

[Lee'sdaytona]

Alright. I'm doing a trans job, and pulled the front mount. Just when I thought I corrected all the hack-job work someone did on this car, there was NO BUSHING! Instead, they welded a steel plate on each side where the rubber would go in, and had a hole drilled in the center! I have no idea what the advantage of this would be, or if anyone would want my mount, but I know I want a factory mount. I've got a new Poly bushing for it.
-Lee

[Lee'sdaytona]

Ok, I found myself a mount. But now I have lost the little clip and bushing that holds the clutch cable on the transmission! Do you have one of these laying around? My car won't be stuck at my buddy's house where we are doing the transmission job, I'll just borrow the clip off my 5-spd turbo caravan if I have to.
I'm sure it will turn up right after I buy one.
Thanks,
Lee

[Dony409]

Yeah I got one but it will be more than a week till it gets there... Your talking the metal peice?

[Lee'sdaytona]

yes the metal piece, and the rubber bushing if you have it. Otherwise I will order from Johnny and Poly Bushings. But hold off for now. I think I clipped it back to the clutch cable (so I wouldn't lose it) and it must have fell off in the engine bay. So this tuesday when I go back to work on it, if I can't find it, I'll use the clip from my minivan and I'll buy yours.
Thanks!
-Lee

[mopardad1]

Driver's door inner panel?

color?
1990 Daytona, drivers door inner panel, looking for gray/black