PDA

View Full Version : NEW Mopar Perf. PT cruiser stage 1 pcms



glhs727
07-21-2010, 11:51 AM
I have 1 module that could be either of the following...
03, 04 or 05 PT ATX Stage 1

I have 1 module that could be either of the following...
06 PT ATX Stage 1 with ABS
06 PT ATX Stage 1 without ABS

I have 1 module that could be either of the following...
03, 04 or 05 PT MTX Stage 1

$300 each
Thanks
Cindy

DC Turismo
07-22-2010, 12:35 AM
Free bump for Cindy. Purchased my Stage 1 PCM from her roughly a month after I bought my GT last May and it was one of the best purchases I've made for it. Can't go wrong with the product or her service! These are a must!

Turbozcs2003
07-22-2010, 01:57 PM
What is the deal, you need cores??

Also what is the odds of a Stg 1 for a 06 PT GT manual trans??? Do you just burn the software onto the cores???



I have 1 module that could be either of the following...
03, 04 or 05 PT ATX Stage 1

I have 1 module that could be either of the following...
06 PT ATX Stage 1 with ABS
06 PT ATX Stage 1 without ABS

I have 1 module that could be either of the following...
03, 04 or 05 PT MTX Stage 1

$300 each
Thanks
Cindy

glhs727
07-22-2010, 02:22 PM
No, I don't need cores. these are NEW from Mopar. If you have an 06 manual, you are probably better off to just use the diabloport (which we also sell)

compdr59
12-24-2011, 12:36 AM
Do you have a Stage 1 PCM for a 2005 PT Cruiser ATX?

glhs727
12-24-2011, 12:45 AM
yes, i do....

wheming
12-24-2011, 10:08 AM
Are these ready to bolt on? New or used?
The one i bought from you required sending to that company (forgot the name) for VIN reprogramming, then when i went to install something wasn't right. Had to send back and they said the final drive ratio was missing and that's what caused no speedo reading.
But this thread reminds me i need to try it and see if it works now!

glhs727
12-24-2011, 11:11 AM
yes, these are good used units that have been thoroughly tested before use. we can have them programmed for you which will add $25 and 3 weeks to the order, or you can have your dealership do the vin. All the PT modules also need the speedo calibrated as well with the correct tire size (that's why the speedo didn't work). If you are local to Houston, and come to our shop with the car, we do the vin and speedo calcs for free...

wheming
12-24-2011, 11:33 AM
What happens when you change tire sizes after having the stage 1 in a while? Like installing larger/taller tires in summer...
Should you do the tranny learn procedure again at that point?
The difference being stock= 205/50R17 to 235/40R17

my android sent this for me using Tapatalk...

glhs727
12-24-2011, 04:00 PM
the programming is really for the height of the tires so the speedo is calibrated correctly. You can go to different size tires as long as they are similar to the overall diameter and not have to redo the pcm. They only give you a couple of tire sizes to choose from in the menu anyway. So going from a 205/50 to a 235/40 should be pretty close and the menu doesn't have any size more accurate so you will just leave it alone...

glhs727
12-27-2011, 06:50 PM
I currently have available:

(2) 2003 pt stage 1 with ATX
(2) 2004 pt stage 1 with ATX
(1) 2006 PT stage 1 with MTX
(1) 2004 PT stage 1 with MTX