Gary Donovans garage sale

[mopar-tech]

http://www.thedodgegarage.com/spirit/the_spirit_1.jpg

I will be posting parts for sale here and rolling over the my SOHC Spirit R/T parts thread, please check back often! Since I no longer have a Turbo Dodge as a daily driver the only parts I'll be keeping are just those related to Reliant racing operations =)

http://www.thedodgegarage.com/spirit/the_spirit_7.jpg

I have a large number of cylinder heads, transaxles (555/568 and even a rare 520 with 2.50 final drive ratio *pending inspection*) that will be up for grabs as well as hundreds of other minor pieces. As they come up in the garage while I'm doing inventory they will be posted here.

Thanks for checking in! Gary Donovan

================================================== ========

Doublecore intercooler with all plumbing, fresh air intake and Talon BOV. $500


89 TII intake with fuel rail and 52 mm throttle body (neck ported) $100


523 transaxle (excellent condition, was rebuilt) $200

New gas tank with extra baffling and new pump $80

A/C lines, compressor & new Modine condensor (SOHC AA) still running R-12! $100

Rear disc brakes ($50)

Front big brake setup with knuckles $75

Springs front and rear $35

Four 16" Lebaron GTC lace rims with 3 good Goodyears LS tire $120

Rear R/T wing $75

R/T rack (no problems) $50

Turbo 2.5 radiator & fan, new from Mopar (not aftermarket junk) $80

87-89 Turbo II fan $20

Turbo II axles $20 each

Fresh ground 8 bolt flywheel $60

Used 8 bolt flywheel $20

Cylinder head turbo complete SOHC $30

SPIRIT R/T 16V UPPER INTERCOOLER HOSE $25
SPIRIT R/T 16V LOWER INTERCOOLER HOSE $25
SPIRIT R/T 16V TURBO TO INTERCOOLER HOSE $25
SPIRIT R/T TURBOCHARGER INLET HOSE $25
SPIRIT R/T 16V BOV INTERCOOLER PIPE $25
SPIRIT R/T 16V UPPER RADIATOR HOSE $5

87-89 radiator and intercooler set with all hoses $250

87 Turbo II intake with fuel rail complete $250


garydonovan@hotmail.com

[roachjuice]

u driving that duster around? thing looks sweet!

[mopar-tech]

http://www.thedodgegarage.com/rwd_mopars/rwd_duster_12.jpg


u driving that duster around? thing looks sweet!

The Duster? Yes about once a week to car shows or work.

Going to bring it to Cecil and put the whip to it hard in November.

[2.216VTurbo]

Paypal ready for the front big brake set up and radiator/fan combo, pm me the total including shipping to 92691 unless you are coming out for Christmas again and you can just bring them with;)

Whats the wire diameter on those rear springs, the TC Masis have the limp .253 dia springs and I've had good luck by changing to HD Daytona springs but have not tried Spirit springs yet.

[turbovanman²]

Subscribed.

I wish shipping wouldn't be a killer, but I would love those GTC rims, :(

[mopar-tech]

Subscribed.

I wish shipping would be a killer but I would love those GTC rims, :(

Where too? I'll be at Cecil in November.

[turbovanman²]

Where too? I'll be at Cecil in November.

Blaine, Wa. 98230

Removing the tires would be even cheaper, I would hope.

[mopar-tech]

Blaine, Wa. 98230

Removing the tires would be even cheaper, I would hope.

Sure, I can pull the tires.

[turbovanman²]

Sure, I can pull the tires.

Can you get me quote, no rush, slow boat to Blaine, :lol:

[bakes]

How much for the 520 2.50 set to the same adress or just the gears out of it to make up the 2.50 raito if that make shipping the easer.

[boost geek]

How much for the 520 2.50 set to the same adress or just the gears out of it to make up the 2.50 raito if that make shipping the easer.

Now what's going on in that head of yours? :D

[bakes]

Remember salt flats idea!

[mopar-tech]

Remember salt flats idea!

That is why I saved the transmission, aside from being a really odd duck!

[roachjuice]

Remember salt flats idea!

salt flat turbomopar. hmmmmmm. id love to see this lol. :D

[mopar-tech]

Stuff added to the first post, every time I add something will bump.

[Mario]

Put me next in line for a price on the trans.

[135sohc]

A/C lines, compressor & new Modine condensor (SOHC AA) still running R-12! $100

I just want to verify. Thats the denso compressor and the low side service port is built into the manifold ontop on the compressor.

[mopar-tech]

I just want to verify. Thats the denso compressor and the low side service port is built into the manifold ontop on the compressor.

see pics on page 3

http://www.turbo-mopar.com/forums/showthread.php?t=37606&page=3

will be a few days guys, i am working off a laptop. the main machine is down.

[mopar-tech]

Main machine back up, still reloading everything though.

[mopar-tech]

2 piece intake and camshaft with sprocket are sold!

[bluneon]

any spare forged connecting rods laying around?

[mopar-tech]

any spare forged connecting rods laying around?

Early TI or TII? I'm sure I do either way.

[cordes]

If Alan didn't take those big brakes, I will. Also, could you send or post pics of the head? If it's in serviceable condition I will take it.

[mopar-tech]

If Alan didn't take those big brakes, I will. Also, could you send or post pics of the head? If it's in serviceable condition I will take it.

Which head? The one of the car is gone but I have another fresh one I was saving.

[cordes]

Which head? The one of the car is gone but I have another fresh one I was saving.

Cylinder head turbo complete SOHC $30

I'm just looking for a serviceable head to go over and put on my shadow without much down time. If you have one that is ready to bolt on or something let me know.

Thanks.

[mopar-tech]

Cylinder head turbo complete SOHC $30

I'm just looking for a serviceable head to go over and put on my shadow without much down time. If you have one that is ready to bolt on or something let me know.

Thanks.

Oh that head, let me look in the garage I have thirteen.

What do you need? bathtube or swirl?

[mopar-tech]

If Alan didn't take those big brakes, I will.

I actually have two sets, let me know your zip and I'll calculate shipping if I have time this weekend.

[bluneon]

Early TI or TII? I'm sure I do either way.

TII rods please.

[cordes]

Oh that head, let me look in the garage I have thirteen.

What do you need? bathtube or swirl?


I actually have two sets, let me know your zip and I'll calculate shipping if I have time this weekend.

I need a swirl head. My zip is 61953. Thanks.

[Turbo Joe]

hey Gary, wondering what the fuel tank fits.. thanx! Joe:thumb:

[mopar-tech]

hey Gary, wondering what the fuel tank fits.. thanx! Joe:thumb:

Well it has the early sump so will work fine with any Daytona / Lancer / Lebaron / Reliant plus the AA which has it's own sump built in the pump housing.

The pump itself is a new R/T unit so I'm running double baffled =)

[thefitisgay]

The pump itself is a new R/T unit so I'm running double baffled =)

sorry to hijack... do the R/T tanks have no baffle in the them? or in other words theres so circle stamped into the bottom its just flat in the middle?

[Badger]

wondering what other body styles the A/C stuff will fit specifically if it will work on an L or P body

[mopar-tech]

wondering what other body styles the A/C stuff will fit specifically if it will work on an L or P body

Just AA I think do to the radiator mounting setup.

[mopar-tech]

sorry to hijack... do the R/T tanks have no baffle in the them? or in other words theres so circle stamped into the bottom its just flat in the middle?

I can't recall at the moment (been a few years since I installed the tank) but I'm 75% the stock AA tank has no "bowl" in the tank.

The bowl is built into the pump hanger on the AA's

I needed a new tank and ended up with one from a Lazer which has bowl of course just popped the R/T pump assembly in.

[LaserGurl]

Im interested in the rear disc brakes... how "complete" are they? Im trying to convert my charger to rear discs.

Thanks,

Tifany

[135sohc]

Im interested in the rear disc brakes... how "complete" are they? Im trying to convert my charger to rear discs.

Thanks,

Tifany

I asked via pm the same question, but then had a change of mind on going with vented discs and didnt persue it further. Its all there

[mopar-tech]

I'll try to get out in the garage this weekend folks and do shipping estimates, busy week with the boss on vacation and having to do two jobs...

[mopar-tech]

The rear discs are vented

[cordes]

Sounds good Gary.

[mopar-tech]

I'll be working on finishing off the Spirit this weekend folks, I'll check in time to time and take pictures as required.

I'm planning on being at Cecil in November so if you want something delivered for free this is your big chance. I also might be at The Valley in New York next weekend.

Gary

[mopar-tech]

LAST CALL! The R/T will be going away on Wednesday so if you need any Spirit body parts let me know. I'll be at Cecil County in November so can bring them (or anything in this thread for sale) then.

There is nothing left attached to the Spirit but the rear seat, dash, carpet and the power brake booster.

The body is all there except for the rear wing, a great chance to get some sheetmetal.

[mopar-tech]

TII rods please.

I do have a single set, let me look to see if I have some more before agreeing to sell this set.

[TopDollar69]

Gary,

Do you still have that K body 5spd shifter bezel you were trying to sell a few years back?

[mopar-tech]

Gary,

Do you still have that K body 5spd shifter bezel you were trying to sell a few years back?

I can look, might take a while though.

[mopar-tech]

Anyone looking for a cheap mig welder? I'm selling my old one for $100

Comes with regulator and (new) hand held face shield.

[TopDollar69]

No big rush, I always kicked myself for not buying it when you first put it up for sale.

[mopar-tech]

The Spirit has left the building.

[contraption22]

It will always be with you.... in Spirit.

HAHAHAHAHA OMG im so funny.

[mopar-tech]

Sorry guys been real busy, once Leahs birthday bash is done with on Saturday should get rolling along again.

[cordes]

Sorry guys been real busy, once Leahs birthday bash is done with on Saturday should get rolling along again.

Thanks for the update Gary, just let us know.

[signsoflife22]

http://www.thedodgegarage.com/spirit/the_spirit_1.jpg

I will be posting parts for sale here and rolling over the my SOHC Spirit R/T parts thread, please check back often! Since I no longer have a Turbo Dodge as a daily driver the only parts I'll be keeping are just those related to Reliant racing operations =)

http://www.thedodgegarage.com/spirit/the_spirit_7.jpg

I have a large number of cylinder heads, transaxles (555/568 and even a rare 520 with 2.50 final drive ratio *pending inspection*) that will be up for grabs as well as hundreds of other minor pieces. As they come up in the garage while I'm doing inventory they will be posted here.

Thanks for checking in! Gary Donovan

================================================== ========

Doublecore intercooler with all plumbing, fresh air intake and Talon BOV. $500


89 TII intake with fuel rail and 52 mm throttle body (neck ported) $100

87 Turbo II shortblock (2% or less ring leakdown) & light flywheel with 4 puck clutch $350 (SPOKEN FOR)

523 transaxle (excellent condition, was rebuilt) $200

New gas tank with extra baffling and new pump $80

A/C lines, compressor & new Modine condensor (SOHC AA) still running R-12! $100

Rear disc brakes ($50)

Front k-member with new control arms (cast) and swaybar $75

Front big brake setup with knuckles $75

Springs front and rear $35

Four 16" Lebaron GTC lace rims with 3 good Goodyears LS tire $120

Front buckets, excellent shape $50

Rear R/T wing $75

R/T rack (no problems) $50

Turbo 2.5 radiator & fan, new from Mopar (not aftermarket junk) $80

87-89 Turbo II fan $20

Turbo II axles $20 each

Fresh ground 8 bolt flywheel $60

Used 8 bolt flywheel $20

Cylinder head turbo complete SOHC $30

SPIRIT R/T 16V UPPER INTERCOOLER HOSE $25
SPIRIT R/T 16V LOWER INTERCOOLER HOSE $25
SPIRIT R/T 16V TURBO TO INTERCOOLER HOSE $25
SPIRIT R/T TURBOCHARGER INLET HOSE $25
SPIRIT R/T 16V BOV INTERCOOLER PIPE $25
SPIRIT R/T 16V UPPER RADIATOR HOSE $5

87-89 radiator and intercooler set with all hoses $250

87 Turbo II intake with fuel rail complete $250


garydonovan@hotmail.com



will the R/T rack (no problems) $50 fit in my GLHS "L" body? And steer well?

[mopar-tech]

Will not fit an L body.

[Mario]

Gary do you have an updated list of what is left? Also, is that trans spoken for, or not for sale yet?

[mopar-tech]

Gary do you have an updated list of what is left? Also, is that trans spoken for, or not for sale yet?

Actually if I have the time I should be able to expand the list- I'll be done insulating my attic tonight and plan on attacking some of the shipping request quotes on Saturday & Sunday.

Remember I can and will be bringing stuff to Cecil! I'd rather carry the large stuff down in the truck than pack it.

Several people are intrested in the trans, I have to check on shipping quotes however.

[bakes]

Was just wondering about the a520 2.50 any word on the shipping Gary
Just wondering were did you find that gear box Mexico ?

[mopar-tech]

Was just wondering about the a520 2.50 any word on the shipping Gary
Just wondering were did you find that gear box Mexico ?

Will be checking today or tomorrow on the shipping, the 520 with the odd gearset is right where I left it =)

Still need time to dust it off and look things over.

[bluneon]

any word on those connecting rods?

[mopar-tech]

any word on those connecting rods?

Nothing I have been able to lay hands on, I might have something in a block but would have to look.

Heading down to Cecil County Maryland to spectate this weekend guys and I'm bringing the truck.

Stuff being brought down- Harness and cluster for Mike, shortblock for Steve, 555 and k-member for Guy.

Anything else? Now is a good chance to get large items that can't be shipped.

If anyone wants them, the front buckets out the R/T are free. Otherwiae they will just end up at the dump/

Gary

[mopar-tech]

R/T buckets are spoken for!

[mopar-tech]

Truck is loaded up, cya at the track!

[Millerman340]

I wander what it would cost to send the seats to Florida?

[mopar-tech]

I wander what it would cost to send the seats to Florida?

The R/T seats are gone

[thedon809]

Hey gary you wouldn't happen to have any stock garrett turbine housing would ya?

[Badger]

Gary,
regarding the T2 axles.......any L body ones? and if so, do they need to be rebuilt?

thanks.

[mopar-tech]

Gary,
regarding the T2 axles.......any L body ones? and if so, do they need to be rebuilt?

thanks.

Just regular Daytona TII pieces, all good and ready to go.

[mopar-tech]

Hey gary you wouldn't happen to have any stock garrett turbine housing would ya?

I don't think I do now, sold the last good one on ebay I think. I did find some compressor housings though..

[Rooster]

still have the wheels?

[mopar-tech]

still have the wheels?

Yes, I have to do some shipping quotes though.

[Rooster]

well what size tires are on them... i probably can come pick them up or if you are coming through nj that works 2...

[guyd_15]

Thanks for droppoing the stuff off, Gary!

We'll get started on the stuff over next weekend. Subframe looks good and cast control arms, he can't wait.

The moly plate important for the trans?

Thanks,
Guy

[135sohc]

Cylinder head turbo complete SOHC $30


523 transaxle (excellent condition, was rebuilt) $200


Turbo 2.5 radiator & fan, new from Mopar (not aftermarket junk) $80


I tried to follow the thread and adjust accordingly. But are any of the above items still for sale ?

Thanks.

[mopar-tech]

Just a bump to let board members getting spooled up to do some more garage cleaning, I have been very busy the last several weeks but things are calming down again.

LMK what ya need.

[135sohc]

Swirl cylinder head ?
523 transmission ?

[contraption22]

Any good usable stock garrets or mild upgrades?

[thedon809]

Non CB 2.2 dipstick tube?

[mopar-tech]

Non CB 2.2 dipstick tube?

I'm sure I have one, there is a box of them in the shed.

[mopar-tech]

Any good usable stock garrets or mild upgrades?

I have a Stocker with a 60 trim wheel and turbonetics housing Mike, low miles

[mopar-tech]

Swirl cylinder head ?
523 transmission ?

Will get on it tomorrow night.

[cordes]

I'm still interested in the big brakes and the swirl head.

[mopar-tech]

Have a dipstick I purchased new when assembling the Spirit, in excellent condition.

To clarify- You need the tube or the dipstick?

[mopar-tech]

I'm still interested in the big brakes and the swirl head.

You need a shipping quote on both? with or without the rotors?

[cordes]

You need a shipping quote on both? with or without the rotors?

Without the rotors. Yes, a shipping quote on both would be great.

[mopar-tech]

Non CB 2.2 dipstick tube?

Have a dipstick I purchased new when assembling the Spirit, in excellent condition.

To clarify- You need the tube or the dipstick?

[thedon809]

Yeah, just the tube. How much shipped to 14802?

[mopar-tech]

Yeah, just the tube. How much shipped to 14802?

$20 fair?

[dusterdude]

i might have missed it but is there a 2 peice intake left?

[R/Tony]

Hey Gary

I want this:
SPIRIT R/T 16V UPPER RADIATOR HOSE $5

give me your Paypal id, thanks!
Tony

[mopar-tech]

Hey Gary

I want this:
SPIRIT R/T 16V UPPER RADIATOR HOSE $5

give me your Paypal id, thanks!
Tony

Plus shipping, need a zip

[tsiconquest88]

pm'd you

[R/Tony]

Plus shipping, need a zip
k... 90650 (Norwalk, CA)

[mopar-tech]

k... 90650 (Norwalk, CA)

I can give parcel a try, $12 shipped

[mopar-tech]

i might have missed it but is there a 2 peice intake left?

Yes I do have a 2 piece with good fuel rail