View Full Version : 4" U bends for Exhaust
Garret
02-23-2006, 10:19 PM
On your site it says you can bend up to 4inch pipe but I see no listings, I really need some 4inch Ubends for a downpipe do you guys have any?
We can actually bend up to 8" tube, but we dont have the die sets. :) We have some u-bends in mild steel.
Garret
02-23-2006, 10:33 PM
Cost?
BadAssPerformance
02-23-2006, 11:05 PM
We can actually bend up to 8" tube, but we dont have the die sets. :) We have some u-bends in mild steel.
So what diamter is the largest you have die sets to do?
4" is the biggest die set we have right now. Die cost at these sizes is pretty insane so we are moving slowly - very slowly into bigger sizes.
On the ubends, I will have to get back to you on a price on monday. I bent these ubends over a year and a half ago so I need to find them and check stock and price on them and make sure they arent a big rusted pile of crap now. :)
Garret
02-24-2006, 12:26 PM
Discounts on big rusted piles of crap ;) because it's for an exhaust lol
Garret
03-09-2006, 01:29 AM
Any word on the 4inch Pipe?
Garret
03-17-2006, 02:38 AM
My downpipe is itching to be made :)
Whorse
03-09-2007, 09:59 PM
I'd also be curious on 4" pipe. B stock is fine as it's exhaust as well.
Nemesismachine
03-15-2007, 12:57 AM
I'm moving that direction too, 4" side exit. The ATP 3" to 4" DP with O2 and wideband bungs looks promising...
We have some 4" x 8" radius in stock. If you guys are looking for a tighter radius, we will have 4" x 6" in early may.
RJ138
04-18-2007, 12:40 AM
We have some 4" x 8" radius in stock. If you guys are looking for a tighter radius, we will have 4" x 6" in early may.
This is good news! I am in the market for 4" diameter bends, the tighter the radius the better. I don't have much room to work with... haha
What is the status and the projected price of these 4" diameter tight radius bends?
Thanks,
RJ
TurbododgePirate
05-07-2007, 05:34 PM
We have some 4" x 8" radius in stock. If you guys are looking for a tighter radius, we will have 4" x 6" in early may.
how much for 1 u piece?
turbovanmanČ
05-07-2007, 07:33 PM
I need a 4x6. LMK when there ready. :D
TurbododgePirate
05-14-2007, 11:26 AM
I still need the 1 4"X8" U bend for my holset... Actually if you have a 90^ that would be better.
TurbododgePirate
08-06-2007, 01:48 PM
okey dokey... it's may.....you have this yet???
Our 4" tooling came in early august -- a few months late. We are going to start product offering early september. Please don't wait on us though. We are running 3 weeks behind as is.
dds78910
08-25-2007, 11:36 AM
If you need 4" exhaust this person might be able to help out.
http://www.weldingweb.com/showthread.php?t=13459
4" Bends are now in stock and added to the website.
-Adam
TurbododgePirate
09-12-2007, 09:31 PM
4" Bends are now in stock and added to the website.
-Adam
SWEET!!!!!!! A 4" 90^ ??
t3rse
10-06-2007, 08:47 AM
too bad you don't have 4 inch v-bands and flanges...
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.