Auto M. A/F, +40 inj, manual bleed and more! Pics!

[shelbymopar89]

*ALL ITEMS DO NOT INCLUDE SHIPPING* Will be shipped from 32068.
Auto Meter Ultra-Lite A/F Used in good shape, works perfect. I cut one of the studs to fit in the pod, when I did it made a bur on the end and the nut threads on hard. Other than that it is in very good shape. $35.00
http://www.shelbymopar.com/gallerybuilder/galleries/For%20Sale/air%20fuel.jpg
http://www.shelbymopar.com/gallerybuilder/galleries/For%20Sale/air%20fuel3.jpg
http://www.shelbymopar.com/gallerybuilder/galleries/For%20Sale/air%20%20fuel2.jpg

+40 Mopar injectors with about 5K on them. PN 4532586 $120.00 takes them all.
http://www.shelbymopar.com/gallerybuilder/galleries/For%20Sale/inj.jpg


Joe P manual boost controler JoePMBC.com.. Performance Products for Turbo Cars. (http://www.joepmbc.com/mbc.html) $25.00
http://www.shelbymopar.com/gallerybuilder/galleries/For%20Sale/joep%20manual%20bleed.jpg
http://www.shelbymopar.com/gallerybuilder/galleries/For%20Sale/joep%20manual%20bleed2.jpg


Set of Federal Mogul +20 rings *IT IS MISSING ONE SECOND GROOVE RING* I do not know what happend to it. $25.00
http://www.shelbymopar.com/gallerybuilder/galleries/For%20Sale/rings2.jpg
http://www.shelbymopar.com/gallerybuilder/galleries/For%20Sale/rings.jpg


Set of Cast control arms. They have been media blasted and are covered with surface corrision. $40.00
http://www.shelbymopar.com/gallerybuilder/galleries/For%20Sale/cast%20control%20arms.jpg

[turbovanman²]

Wheres the bleed?

Shipping on control arms to 98230 please.

I'll take the rings if there turbo rings. :clap:

[shelbymopar89]

The bleed is what I refered to as the JoeP boost controller, sorry if I confused you. I will check on the shipping tom for you. They are turbo rings.

Also have a 190 l/hr fuel pump, also around 5k on it. From FWD Performance, here is their writeup. Works perfect. $50.00
Our Walbro/Holley fuel pump replaces the in-tank pumps for quiet operation and longer life. Pump flows 190 l/hr and flows approx. 25% more than stock. These are direct replacements for 85-90 vehicles and can be used in 91-93 vehicles with some modifications.
http://www.shelbymopar.com/gallerybuilder/galleries/For%20Sale/fuel%20pump.jpg

[Mario]

What vehicle are the control arms off of?

[shelbymopar89]

Greddy Type-S BOV. I will get a better picture of it up on here tomorrow. Works just dandy. Includes flange and pipe seen in the picture. $100.00
http://www.shelbymopar.com/gallerybuilder/galleries/Exterior/car%20show.jpg

Mario,
They came off of a 89 (I think it was 89) Spirit RT. I will double check that for you.

[Mario]

I'll pass then thanks

[shelbymopar89]

If you kike something, but not the price shoot me an offer.

[turbovanman²]

Price on shipping for the control arms? ;)

What are the arms off? seemed to turn Mario off? :confused:

And yes, I'll take the rings.

[Mario]

Not to steer someone in another direction from buying the control arms:

If I "upgrade" I'm either doing minivan control arms next, or I'm going to see about getting tubular ones done up.

[turbovanman²]

Not to steer someone in another direction from buying the control arms:

If I "upgrade" I'm either doing minivan control arms next, or I'm going to see about getting tubular ones done up.

Cast Mini's and cars are the same arm, ;)

[Mario]

Cast Mini's and cars are the same arm, ;)

Not to go too far off topic but I thought they were different. Is that the stamped only? What's better, stamped or cast?

[turbovanman²]

Not to go too far off topic but I thought they were different. Is that the stamped only? What's better, stamped or cast?

Ok, 90 and older use stamped arm which is identical to the cars except the dual pivot stamped arm used on the 11 inch brake cars. The only difference on the van is there braced, so there alot stronger. To use a cast arm on the Minivan, you have to swap in the 91 and up 2nd Gen K-member, and matching knuckles, car wheel bearings and either car 11 inch rotors, van 11 inch calipers or car/van 10 inch rotors and calipers. Stamped are lighter, cast is heavier but they have a better alignment curve. Also, used the cast setup enables you to use the RT/GTC 11 inch brakes, ;)

[shelbymopar89]

Price on shipping for the control arms? ;)

What are the arms off? seemed to turn Mario off? :confused:

And yes, I'll take the rings.


You would be looking at $15.00 for shipping. The arms are off of a 89 Spirit RT. Turbovanman you do know that the rings are missing on of the second groove right? Just want to make sure.

[turbovanman²]

You would be looking at $15.00 for shipping. The arms are off of a 89 Spirit RT. Turbovanman you do know that the rings are missing on of the second groove right? Just want to make sure.

Is an 89 RT a new model? :lol:

Sold, and yes, I know about the missing ring, I have a few sets here missing rings due to me breaking them on install, :clap:

[shelbymopar89]

Is an 89 RT a new model? :lol:

Sold, and yes, I know about the missing ring, I have a few sets here missing rings due to me breaking them on install, :clap:

LOL, Had a brain fart, don't rightly know what I was thinking. 91 is what I ment.

[shelbymopar89]

Adding Pics
http://www.shelbymopar.com/gallerybuilder/galleries/For%20Sale/bov4.jpg
http://www.shelbymopar.com/gallerybuilder/galleries/For%20Sale/bov5.jpg
http://www.shelbymopar.com/gallerybuilder/galleries/For%20Sale/bov6.jpg
Everything shown is included.
Stock used MAP sensor $10.00
http://www.shelbymopar.com/gallerybuilder/galleries/For%20Sale/map.jpg

[shelbymopar89]

A/F-Sold pending payment
Injectors-Sold
Rings-Sold pending payment
Control Arm-Sold Pending payment
Greddy-Sold pending payment
Joe P Boost Ctl- Sold pending payment

Still Avail
Fuel Pump
Stock Map

[jl93sundance]

If the deal on the greddy bov falls through, ill take it, just send me a pm

[shelbymopar89]

If the deal on the greddy bov falls through, ill take it, just send me a pm

Sounds good, you are thrid in line.