Exterior window felt/trim for 87 Daytonas still available?

[Clay]

I know these are impossible to find for L-bodies, but are they available for an 87 daytona? this is the felt/rubber seal that goes up against the outside of the window. One side on my daytona is shot.

thanks,
clay

[mwrenn]

Try www.arizonaparts.com, they have an online parts list if you have the number of your trim. I was able to locate three of the four trim parts for my lancer on their site. Haven't tried calling and ordering yet though. Hope this helps.

Mike

[spoolinhard]

I have found them in j-yards on newer tonas in great shape.

[Clay]

do all of the daytonas use the same piece??

[rich tideswell]

yes, the window felts should be the same (hell they used almost the same door the entire legnth of time the car was produced)

i wouldn't at all be shocked that the felts are common amungst the lebarons, shadows, spirits, accliams....etc.......

[JeremyL]

I got new felts from the dealer about a year & a half a go or so. One was in Dallas, and the other came from someplace up north. I just cut the little notch one one end since my car has t-tops, and they worked perfectly.

[mcsvt]

Yup all the same size besides the t-tops as Jeremy mentioned. JDAWG could probably tell you if any are still sitting on the selves anywhere.

[Clay]

on the phone with the local dealer as i type this :)

[Clay]

well, the part number is 4198670. Its NS1, and no dealers on the network show any in stock.

SOOOOOO Im back to looking for a decent/good used one.

thanks,
clay

[spoolinhard]

well, the part number is 4198670. Its NS1, and no dealers on the network show any in stock.

SOOOOOO Im back to looking for a decent/good used one.

thanks,
clay

I more than likely have a set, I will check this weekend
-Kaleb

[mwrenn]

AZparts shows 9 in stock, $75 each though. OUCH!!

[Clay]

I more than likely have a set, I will check this weekend
-Kaleb

that would be great!

[Clay]

AZparts shows 9 in stock, $75 each though. OUCH!!

I found another place that says the have them in stock for a LOT less. Im waiting on their reply, and another. ;)

[rich tideswell]

have you tried glueing some new felt onto your old pads? kinda a ghetto fix, but its better that scraping the window up

[Turbodave]

Clay the ones on the 88 Daytona I've got are nice, if you want them let me know.

[mwrenn]

I found another place that says the have them in stock for a LOT less. Im waiting on their reply, and another. ;)

Yeah, I thought that was pretty high.:confused: Moparpartsamerica.com has them for $53. Much better!:clap:

Mike

[Clay]

Yeah, I thought that was pretty high.:confused: Moparpartsamerica.com has them for $53. Much better!:clap:

Mike

but they cant get them. They are NS1, and so I emailed moparpartsamerica.com to see if they had some..... no dice.

[mwrenn]

That sucks! Did you find another source for them? I'm trying to get a belt molding for the right rear door of my Lancer.

[Clay]

I found a used set.

[mwrenn]

Cool, thanks!

Mike

[Aries_Turbo]

im bumping this old thread to see if anyone has any of these.

Brian

[martin kolner]

4198670-1 R/L 1984-91 G body ONLY non-t-top

I have them www.arizonaparts.com

[1966 dart wagon]

dam i feel lucky i found 2 sets in great condition at the local you pull it yard, and it was on a all you can pull for 40 bucks day, pulled both sets, and a whole head/intake/exh/turbo, just that alone was worth it not counting all the extra bs i got :D

Good luck finding them guys

[rich tideswell]

im bumping this old thread to see if anyone has any of these.

Brian


i have 2 driver side mouldings. both came off my 88

http://i49.photobucket.com/albums/f297/rtideswell/daytona%20parts/1988daytonawindowscrapers.jpg

http://i49.photobucket.com/albums/f297/rtideswell/daytona%20parts/1988daytonawindowscrapers2.jpg

http://i49.photobucket.com/albums/f297/rtideswell/daytona%20parts/88daytonacrapperfelt1.jpg

http://i49.photobucket.com/albums/f297/rtideswell/daytona%20parts/88daytonascraperfelt2.jpg

[Aries_Turbo]

what do you want for them shipped to 14569.

Brian

[rich tideswell]

what do you want for them shipped to 14569.

Brian

I'm asking $10 for both parts + shipping. I'll box them up and get you a quote.

[Aries_Turbo]

10$ each or 10$ total?

Brian

[iangoround]

For $10 and shipping I'd go for that, but you can also make your own using generic parts from JCWhitney for less than $50 shipped.

http://www.turbo-mopar.com/forums/showthread.php?t=33106

Also, I have a passenger side one on my parts car still. I think I cut up the driver side in an experiment.

[Aries_Turbo]

i already have dibs on it you stinker. :)

Brian

[rich tideswell]

10$ each or 10$ total?

Brian

$10 total for both parts + shipping. you send me $10 + shipping cost, I send you both parts pictured :thumb:

And to clarify these are for NON t-top and both fit the driver side

[iangoround]

Sorry that read wrong, I wasn't expressing interest in them. I already replaced mine with JC Whitney stuff. :thumb:


i already have dibs on it you stinker. :)

Brian

So if his are both driver side parts, you can have my passenger side one for a few bucks and have yourself a complete set.

[Aries_Turbo]

oh so they arent interchangeable?

yeah lemme know how much the shipping will be.

ian, ill take yours then. you gonna be at the sdac meet on friday?

Brian

[iangoround]

No, I've got a 14+ hour day at the work that day. I'll be out at the shop in Hamlin on Monday. You can drive out if you want, or I can ship it out or something.


oh so they arent interchangeable?

yeah lemme know how much the shipping will be.

ian, ill take yours then. you gonna be at the sdac meet on friday?

Brian

[Aries_Turbo]

pm me your number. ill give you a shout to see when i can stop by sometime. i work all over the place and dont know where ill be then.

Brian