Customer Project By SMP

[SMPerformance]

Here is the next car being built at SMP

mercury Capri
sds engine management
engine Dart block
Yates cylinder heads Ported by Richard poudrier racing heads
SMP custom turbo kit

here are a few teaser pics

customer wants 1500hp will we do it :eyebrows:

[turbovanman²]

Aweome, :thumb:

Keep us updated with pics and the final dyno session.

[altered7151]

Wow, make sure you keep any pets and small children away from that turbo on startup!

[cordes]

Wow, make sure you keep any pets and small children away from that turbo on startup!

Oh, come on. I don't think that little thing could suck in an animal any bigger than a goat. A cow absolute tops.

[GLHSKEN]

Good God... Look at that SNAIL!!

[BadAssPerformance]

Sweet ride!

btw, moved the thread to 'other vehicles' as its not a mopar...

[Frank]

and old T76 turbo - garrett/airesearch???


Frank

[SMPerformance]

and old T76 turbo - garrett/airesearch???


Frank

thanks for moving the thread

That is the mock up turbo it's a T-76 DBB
The turbo for the car is a Turbonetics 106mm Ball Bearing Turbo being built has we speak

I will keep this updated as we are starting to built the headers next week

also will post in the td section about a street 1987 SC being built here for a customer T-III engine,A-413 tranny big turbo basicely my drivetrain in a street car

[BadAssPerformance]

thanks for moving the thread

That is the mock up turbo it's a T-76 DBB
The turbo for the car is a Turbonetics 106mm Ball Bearing Turbo being built has we speak

I will keep this updated as we are starting to built the headers next week

also will post in the td section about a street 1987 SC being built here for a customer T-III engine,A-413 tranny big turbo basicely my drivetrain in a street car

No problem :thumb:

The 106mm turbo ought to do it... updates will be cool too!

'87 SC sounds BadAss!

[slasky]

Wow! I wish my turbo was so big I needed an engine hoist to lift it up and down too!

[WVRampage]

How many cubes is that engine.

[Mike_Shepard]

I seen a GT42 yesterday and thought that was big..... my lord

[Ondonti]

I believe the gt42 will outdo the t76 though wont it?

[SpoolinGLH]

lol yeh you know its bad when you have to have a cherry picker holding up your turbo haha

[89DaytonaTII]

Nice!

Reminds me of a "street car" mustang from Calgary, 347 dart block + 106mm turbo = low 8's at 170mph on DR's. :eyebrows:

[Frank]

I believe the gt42 will outdo the t76 though wont it?

Actually they top off at about the same. However the GT42 has better spool up and less surge area. Both are good for about 1000hp... plus or minus about 100. However Stephane... isnt the turbonetic 106mm the same as a T76?????


Frank

[BIG PSI]

thanks for moving the thread

That is the mock up turbo it's a T-76 DBB
The turbo for the car is a Turbonetics 106mm Ball Bearing Turbo being built has we speak

I will keep this updated as we are starting to built the headers next week

also will post in the td section about a street 1987 SC being built here for a customer T-III engine,A-413 tranny big turbo basicely my drivetrain in a street car

Frenchy;

What do I have to do to get you to work your majic on one of my MINI's ???
I keep waiting to hear from you.

Chuck

[SMPerformance]

How many cubes is that engine.

the engine is 374cid


However Stephane... isnt the turbonetic 106mm the same as a T76?????

basicely yes but the customer is having a custom turbo (exhaust wheel) done by turbonetics with a dBB center section they are sponsoring the turbo for the car
he wants the car to be street driven his wish is to drive to the track run low 8's and drive home:nod:


Frenchy;

What do I have to do to get you to work your majic on one of my MINI's ???
I keep waiting to hear from you.

didnt we talk about this a couple of months ago ?? please refresh my merory

send me a pm

[SMPerformance]

started on the headers

[cordes]

started on the headers


That is truly a work of art.

[SMPerformance]

That is truly a work of art.

thanks we try are best ;)

here is one side done just have to weld the v-band on the collector

[8valves]

thanks we try are best ;)

here is one side done just have to weld the v-band on the collector

Those are some tight confines for sure. Stephane, do you use the 94 or 102 wheel in your 42R?

Aaron Miller

[Ondonti]

94mm FTW

Thats a single plane intake manifold right?

[SMPerformance]

Stephane, do you use the 94 or 102 wheel in your 42R?

Aaron Miller

:eyebrows: check pm's


Thats a single plane intake manifold right?

yep single plane with the Yates C3 series heads


here are more pics right side header is almost done still waithing on those dang V-Bands:banghead:

oil pan is also done and we started on the piping

[mcsvt]

Looks great :thumb: thanks for the updates :)

[SMPerformance]

Looks great :thumb: thanks for the updates :)


here are a few more pics intercooler being fabbed and done

[Frank]

I think you should talk about that head sitting on your bench. :D I see welding on the ports... did you do someting. :)

[Clay]

Ohhhhhhhhhh good eye! goooood eye! :eyebrows:

[SMPerformance]

I think you should talk about that head sitting on your bench. :D I see welding on the ports... did you do someting. :)

hey hey Frank just preparing a new cylinder head for the car got to get ready for the imports dont want to let TM.com down lol :thumb:

[mcsvt]

Yeah don't let us down :D and is there a schedule some where that we can see what tracks you will be at?

[Frank]

Yeh that would be cool. I am going to assemble a SMP page for on the front portal page... we can put that and his racing results there.


Frank

[mcsvt]

Yeh that would be cool. I am going to assemble a SMP page for on the front portal page... we can put that and his racing results there.


Frank

Excellent :thumb:


[smilie=2,38,39]

[bansheenut420]

You guys do truly AMAZING work. Keep it up :thumb: Kick some import A** next year!:nod:

[SMPerformance]

piping from intercooler to throttle body is done with twin 50mm Tial blow off valves

[8valves]

I've been waiting to see people mounting BOV's like that in line with flow. Same with wastegate's, not too many peolpe seem to take head to it.

Holy gauges on the cowl though!!

Aaron Miller

[SMPerformance]

Holy gauges on the cowl though!!

Aaron Miller

not my idea lol :yuck:


HKS 60mm GTII wastegate installed

[Dave]

God, that's sexy.

[turbovanman²]

Nice work, :thumb:

I was going to comment on the head mods too, but Frank beat me to it, :nod:

I had to think a bit about the BOV mounting but now it makes perfect sense, :D

[johnl]

not my idea lol :yuck:


HKS 60mm GTII wastegate installed

THAT is some nice welding!

[WVRampage]

All that piping under the hood and looking that good is amazing, you guys do great work, cant wait to see the dyno numbers on it.

[87 charger]

hey hey Frank just preparing a new cylinder head for the car got to get ready for the imports dont want to let TM.com down lol :thumb:


Will you be back in St.Louis this year at nopi ? I really wanted to see your monster in action,but you had tranny issues at the time. If you are going to make it out there again then I am going to make the drive out again !:thumb: :thumb:

[Dave]

Any update Stephane?

[Dave]

Update??

[20w/ashelby]

new pics?

[heavytank2]

Header pipe looks a bit thin?

I am used to heavy iron/steel. Whats the material?

[Frank]

Last I heard, stephane was busy racing and with someone gone from his shop, he doesnt have much time here and doesnt post much.


Frank

[mpgmike]

I think you should talk about that head sitting on your bench. :D I see welding on the ports... did you do someting. :)
Well thanks alot! :mad: I bet he's more careful about what he lets sitting in the background next time :faint:

[Frank]

Uhhh?????

[Clay]

Yeah, hunh???????????????????????

[mpgmike]

We got to see something he apparently didn't want us to. But since you brought it to his attention, he will be more conciencious about what ends up in pictures (protect his proprietary secrets, you know).

[Frank]

Actually he hasnt ever been like that at all. Things I have spotted in the past he has told us about.


Frank

[turbovanman²]

We got to see something he apparently didn't want us to. But since you brought it to his attention, he will be more conciencious about what ends up in pictures (protect his proprietary secrets, you know).

No secrets, make ports F*cking huge, nuff said, :eyebrows:

[Reaper1]

I've got two questions about this project.

#1, is there going to be any more support for the turbo other than the headers?

#2, what size are the primaries and the "up-pipes" after the collectors?