Activity Stream - Turbo Mopar Forums

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Articles Articles Knowledge Center Knowledge Center

Today, 03:26 PM

Reaper1 replied to a thread Boost drifting downward in EFI Tuning

What is the setup of the car? There's a lot of things that can cause a dropping boost curve.

1 replies | 23 view(s)

Today, 09:51 AM

jeff1234 started a thread Boost drifting downward in EFI Tuning

I was studying my most recent mpscan plot and noticed that above 4000 rpm boost was dropping while rpm continued to rise. It wasn't much, about a...

1 replies | 23 view(s)

Today, 06:42 AM

bgbmxer replied to a thread Well I tried... in Transmission

Wondering the same

19 replies | 478 view(s)

Today, 06:39 AM

bgbmxer replied to a thread Well I tried... in Transmission

Did they offer an unequal length setup in the dynasty or would one be able to make one with the correct center shaft?

19 replies | 478 view(s)

Today, 03:09 AM

GLHS60 replied to a thread DriveShaft Shop Axles - Group Buy in Group Buys

I have a pair of OEM inner CV's only from a 1987 Shelby Z if anyone needs them. I had the shafts shortened but it didn't work out and I saved the...

401 replies | 82268 view(s)

Today, 03:03 AM

GLHS60 replied to a thread Gaskets in Maintenance & General Tech

It's not recommended to use a gasket on the int shaft seal retainer. Anaerobic sealer. Mopar prefered. Thanks Randy

4 replies | 121 view(s)

Yesterday, 02:22 PM

Dr. Johny Dodge replied to a thread Well I tried... in Transmission

so I guess a pair of Detroit axles iroc r/t axles will do ..for now at least - I'm planing to use a dual pivot cross member without narrowing it .....

19 replies | 478 view(s)

Yesterday, 12:44 PM

Fenderbass replied to a thread How to Modify A413 for More Power in Transmission

does anyone have a good picture of a homemade version of that Miller tool used to compress the direct clutch return spring?

24 replies | 600 view(s)

Yesterday, 12:16 AM

CSXVNT12 replied to a thread Shelby Lancer Rear Disk Brakes Caliper Pins in Shelby Models - Whittier Factory Cars

You can add Raybestos H5015W to the parts that Do Not fit list.. -- This is also a 13mm caliper pin, but again it has the wrong 10x1.25 thread, the...

4 replies | 186 view(s)

01-16-2021, 10:22 PM

cordes replied to a thread Gaskets in Maintenance & General Tech

Rockauto usually has those sets for really cheap. Amazon generally does too. I wouldn't hesitate to use the Felpro gaskets, but I've recently seen...

4 replies | 121 view(s)

01-16-2021, 09:54 PM

Wastelands Warrior replied to a thread Well I tried... in Transmission

Problem is Detroit Axle is out of stock for the longer CV axle.

19 replies | 478 view(s)

01-16-2021, 09:01 PM

TopDollar69 replied to a thread General Looking for Turbo II Wiring Harness in Parts Wanted

Pm sent.

6 replies | 242 view(s)

01-16-2021, 08:06 PM

Slam92 replied to a thread Gaskets in Maintenance & General Tech

I’m gonna try out the head gasket it looks good it just has some extra holes compared to the MP gasket that I took off. Sent from my iPhone...

4 replies | 121 view(s)

01-16-2021, 07:43 PM

ajakeski replied to a thread Well I tried... in Transmission

I bought a set of Detroit axles for my van after another member said he had good luck with them. They cost around $80 for the pair, shipped for free...

19 replies | 478 view(s)