Activity Stream - Turbo Mopar Forums

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Articles Articles Knowledge Center Knowledge Center

Today, 03:32 AM

Dr. Johny Dodge replied to a thread Oil pan install in Maintenance & General Tech

toss the cork gaskets buy tube of quality silicone buy end seals apply silicone to pan rails service manual calls for silicone in the 90*...

2 replies | 15 view(s)

Today, 12:01 AM

EaZyE426 replied to a thread Well I tried... in Transmission

Detroit Axle has long CVs in stock now.

26 replies | 1784 view(s)

Yesterday, 11:20 PM

EaZyE426 replied to a thread Oil pan install in Maintenance & General Tech

If you have the ability to use the one piece gasket, may be 89+ only, I don't recall, it's the best. But use a little rtv at each end of the rubber...

2 replies | 15 view(s)

Yesterday, 11:19 PM

Barraguy started a thread Oil pan install in Maintenance & General Tech

The 2 rubber end gaskets. Should they be installed dry, or should RTV be used on them? I know to do the gasket/seal junction with some. What are you...

2 replies | 15 view(s)

Yesterday, 10:32 PM

EaZyE426 replied to a thread Will this 3Bar Map work? in "I need help!"

https://www.diyautotune.com/product/map-gm-3-bar-map-sensor/ I didn't get the pigtail as you can slightly modify the stock plug to fit this sensor...

3 replies | 57 view(s)

Yesterday, 10:17 PM

Simsy replied to a thread Will this 3Bar Map work? in "I need help!"

can you post a link to it ?

3 replies | 57 view(s)

Yesterday, 10:08 PM

Reaper1 replied to a thread Underdrive pulley belt sizes in Maintenance & General Tech

Time to pin Brent's post to the KC!

67 replies | 12337 view(s)

Yesterday, 10:07 PM

EaZyE426 replied to a thread Will this 3Bar Map work? in "I need help!"

It is, but I would question it's quality at $20.00. I'm using the one from DIYAutoTune for my R/T and it works great.

3 replies | 57 view(s)

Yesterday, 08:52 PM

Simsy replied to a thread General Part-out / Cleaning...Bigstuff3 ECU, ID injectors, wiring harnesses..etc in Parts For Sale

Is the 3 bar map a genuine GMsensor ?

10 replies | 1206 view(s)

Yesterday, 11:32 AM

Reeves replied to a thread M&H Tire Discount Code in Suspension, Brakes, Wheels, Traction

NEDRA still works. Saved $45.80

14 replies | 7706 view(s)

Yesterday, 04:39 AM

bgbmxer replied to a thread Well I tried... in Transmission

More info on this. Litterly haven't a clue who your referring to but am interested

26 replies | 1784 view(s)

Yesterday, 01:45 AM

Simsy started a thread Will this 3Bar Map work? in "I need help!"

hey guys, would this be the correct 3 Bar Map and pigtail to use on my 91 Spirit R/T? ...

3 replies | 57 view(s)

Yesterday, 01:23 AM

GLHS60 replied to a thread 1988 K-car style LeBaron sedan rear wheel cylinder questions. in Suspension, Brakes, Wheels, Traction

Saturday was what I would call successful in a one handed way. I got the flex hoses attached to the main steel line and clipped to their brackets....

23 replies | 451 view(s)

Yesterday, 12:53 AM

GLHS60 replied to a thread Stamped letters on rails in Engine - Block, Piston, Heads, Intakes

Naturally the pistons are also stamped to allow select fitting of pistons/bores. Thanks Randy

3 replies | 61 view(s)

03-07-2021, 10:23 PM

trannybuster replied to a thread For Sale Selling all cars and motorcycles because of health in Cars

Feel SOME of your pain...was in coma for week with peg tube for feeding and a trach... until I woke up and pulled them both out,,,,then they subdued...

32 replies | 2639 view(s)

03-07-2021, 09:18 PM

cordes replied to a thread 84 T1 Laser XE in Project Log

That looks great. Nice work.

20 replies | 5572 view(s)