Activity Stream - Turbo Mopar Forums

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Articles Articles Knowledge Center Knowledge Center

Today, 12:04 AM

cordes replied to a thread Head Porting in Engine - Block, Piston, Heads, Intakes

Thanks again for all the replies everyone. Here are some progress pics. Note that' I'm experimenting with this junk head, so this is far from...

22 replies | 403 view(s)

Yesterday, 08:52 PM

TurboShock started a thread General Looking for front floor pans for a 1989 Dodge Daytona in Parts Wanted

I am looking for front floor pans for a 1989 Dodge Daytona (not sure if other years will fit but if you have one for another year send a pic so I can...

0 replies | 28 view(s)

Yesterday, 08:09 PM

TurboShock replied to a thread Interior Looking for a passenger front outer seat recliner for 89 Daytona in Parts Wanted

Sorry for the delay in getting back to you, I’ve been busy... Not sure how to post pics on here but the part I need is the mechanism connected to the...

6 replies | 288 view(s)

Yesterday, 05:36 PM

chromguy replied to a thread 2.4L SMEC base cal questions and mods in Electrical & Fuel System

Yes I agree it is a PITA.

3 replies | 75 view(s)

Yesterday, 05:02 PM

player1up replied to a thread 2.4L SMEC base cal questions and mods in Electrical & Fuel System

I was afraid of that, most of the conversation has moved there. Unfortunately searching social media after the fact is lame.. :/

3 replies | 75 view(s)

Yesterday, 04:23 PM

chromguy replied to a thread 2.4L SMEC base cal questions and mods in Electrical & Fuel System

I believe a number of folks on FB maybe able to comment as well

3 replies | 75 view(s)

Yesterday, 02:36 PM

zin replied to a thread Billet forward and direct drums in Transmission

Of all the custom Auto parts being made, I think this one makes the most sense for the most people, it allows a serious upgrade and serviceability...

15 replies | 1878 view(s)

Yesterday, 02:34 PM

player1up started a thread 2.4L SMEC base cal questions and mods in Electrical & Fuel System

Who's using the 2.4L base cal and how well does it run out of the box? What timing changes should be made when switching from the ski ramp pistons...

3 replies | 75 view(s)

Yesterday, 01:34 PM

MaxHeadroom replied to a thread A413 31TH Alto Power Pack Red Eagle Frictions and Kolene Steels Group Buy in Transmission

PM’d you. Sent via Telegraph

33 replies | 1602 view(s)

Yesterday, 12:31 PM

Turbo SOB replied to a thread Omni GLH Turbo suddenly dead in "I need help!"

It could have still jumped a few teeth. In fact, that just happened to one or our local members on his Shelby Lancer. Nothing made sense, everything...

7 replies | 143 view(s)

Yesterday, 11:10 AM

Shadow replied to a thread Head Porting in Engine - Block, Piston, Heads, Intakes

I think the easiest way to think of porting is somewhat the same as choosing a cam; According to valve size, where do you want your power to be?...

22 replies | 403 view(s)

Yesterday, 06:25 AM

raccoon replied to a thread Omni GLH Turbo suddenly dead in "I need help!"

I would compare two parts. hoping for the similar values. might find something open then it would be obvious

7 replies | 143 view(s)

Yesterday, 02:31 AM

nvysion replied to a thread 2.5L TIII distributor in 2.2L/2.5L 16V Hybrid conversions

It is a 1989 SMEC

17 replies | 776 view(s)

02-20-2019, 11:47 PM

tryingbe replied to a thread Omni GLH Turbo suddenly dead in "I need help!"

Sorry to hear about your CSRT. :(

7 replies | 143 view(s)

02-20-2019, 10:32 PM

iTurbo replied to a thread Omni GLH Turbo suddenly dead in "I need help!"

Thanks guys, I will check all those. I don't have a scope though. I'm sure I have another power module around here somewheres. Also, I forgot...

7 replies | 143 view(s)

02-20-2019, 10:09 PM

Dan H replied to a thread DRB II LCD Modification in Electrical & Fuel System

I forgot about the picture. I think I'm probably past being able to use the conductive glue. Looks like the connection completely broke on the...

18 replies | 1973 view(s)